Jump to content
SAU Community

Recommended Posts

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

was hoping it was the spark plugs in my mind but have a feeling its not. plus when its idling and about to move forward in 1st.... i can hear a belt squeek in a way, been testing it while holding the brake and letting the clutch out i can hear it more......... its never done it before til this pinging noise.....

this car is my daily car, be hard for me to get around.......... imo ....its really annoying :)

sparkplugs won't cause detonation, they can but it is highly unlikely in your situation, it almost certainly CAS base timing is advanced, you are not running 98 octane fuel, or it is a fuel issue and is leaning out.

Get it on a dyno and diagnose the issue, don't keep driving it or you WILL destroy the motor.

+1 have a look at the CAS position , see if someones been messing with it.

.. imo ....its really annoying :)

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

having to replace the motor will be even more annoying, do not rev it past 4k and no boost until this is solved, I don't think you realise how serious this is. 10 seconds on full boost with sustained detonation is enough to melt ring lands.

yeah! what he said!!:spank:

Exaclty, it'll be your base timing is too advanced or you have a lean out due to stuffed fuel pump, blocked injectors, broken fuel reg or blocked fuel filter.

Stop wasting time with all the other shit and get it to a proper workshop so they can stick a wideband in the exhaust and a timing light on then diagnose it as either timing or fuel.

Edited by Rolls

Would make more sense as it is extremely common for an annoying misfire at peak torque with stock tune skylines.

Pinging sounds like marbles being shaken around in a tin can, misfire sounds like the rev limiter, pop pop pop

Edited by Rolls

no need for a timing belt, timing light gave me a good reading

Just checking - you realise those two things are unrelated, right? I can't tell from your post.

The cam timing can be off and the spark timing can be fine, and the cam belt can be well past its reliable life, and the spark timing can be fine.

misfire sounds like the rev limiter, pop pop pop

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

it was making that noise heaps when hitting around 4000rpm... and also the pinging noise was just the intercooler pipe hitting the fan. ive replaced with a shorter bracket which pulls it away from the fan and sits nice and close to the timing cover.

i have fixed both problems but im in the proccess of getting a dyno and buying a timing kit, water pump cam belts. i am doing my best here in researching and learning more about the car.

might help to get your terminology right next time, would have give a completely different answer if you said misfiring and not pinging. Completely different things, detonation destroys motors, misfire is just annoying.

Elite/Rolls - holding all other things the same, wouldn't hot plugs slightly increase the tendency to ping?

I'm pretty sure a 5 is the hottest plug you can get in that size/thread/depth whatever. The factory listing is a 5. Like Rolls said, most unlikely.

Not impossible though. Usually dieseling is caused by lack of ignition timing or very lean mixtures

hmm well i had two sets of problems with the car... noises coming from here and there. The hitting noises were the fan hitting the intercooler pipe making the *tinging* noises .... thats fixed now..... and 4 out of 6 spark plugs were just absolutely f**ked..... i did buy NGK plugs.... good buy, fixed the misfire. currently driving the car at 2500 - 3000rpm. Everything seems to be fine ATM, but you guys have commented on the timing and cam belts, so i will be replacing them when i can.... i have seen the belts and they have seen better days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...