Jump to content
SAU Community

Recommended Posts

The radiator may have been flushed, but what about the block. There's always the scenario that that crap is coming from the block, even if the block was flushed also. There will always be little traces of gunk that will filter thru the motor at a later time.

Seeing as there is no chocolate milkshake in your sump, and only small traces of oily residue on your cap, I'd do a pressure test at a starting point. Then monitor the radiator and oil in sump at weekly intervals if the leak down test is okay. Just keep an eye on it for now.

:thumbsup:

Update:

Today I got the car compression tested and TK tested (checksfor combustion gasses in the coolant).

Compression results were as follows: 1. 155 2. 160 3. 135 4. 145. 5. 160 6. 160.

TK test showed NO sign of combustion gasses in the coolant.

When I first dropped the car off and left they called within15 minutes asking for me to come back as they wanted me to show them what I wasworried about because at the time when they first pulled the cap of their wasno oil or anything around but by the time i walked back a little bit hadbubbled up. Mechanic assumes that the headgasket might be on the way out but it’sin its VERY early stages.

He suggested that I lower the boost (currently at 12psi) becausesometimes It hits fuel cut when you boot it (saying that this is very rare as Ibaby it mostly...) and that I just monitor the temperature and oil and coolantlevels.

Just after a couple more opinions on it, perhaps I shouldjust monitor it and keep my eye out for a wrecked stag and buy the donk....

Rough prices was $1500 for head gasket (metal) replacement aslong as my head is fine or worst case scenario $2500.

Thanks once again guys J

Edited by kidafa

oil in your radiator is not good but can still be driven for a short distance (depending on the amount)

however, water in your sump means "turn engine off immediately"!

Just because a TK test showed NO sign of combustion gasses in the coolant, doesn't mean that there isn't a track between an oil gallery and a water jacket, either via a crack or a damaged head gasket. Head gasket may be sealing the cylinders well hence no drastic drop in compressions.....damage obviously elswhere.

My suggestion is to flush both oil & cooling system out then start again and monitor very closely...........do not boost its head off in the meantime!

throw in a bottle of iron tight with clean water then dump it after a week and fill with normal coolant could go for yrs once its had this treatment . ive seen sprintcar engines leak like a sieve and one treatment of this they see a season out ..

Same thing happened to me last year

Comp test was fine, as was leakdown, however pushing the 20 year old oem gasket to 19psi blew the seal between the cylinder (which the surrounding gasket was already deteriorated for 1cm in diameter around the whole thing) until it met the water lines. The amount of oil in the rad wasn't huge, but I wasn't going to risk it.

Thankfully Ruby was a champ and was able to strip it down and fit a new cometic mls gasket for me, and its been running beautifully ever since it was tuned up to the new gasket/bolts/all other stuff ruby got me to replace.

Chances are if you've got a 20 yr old car that hasn't had the gasket replaced, its kaputski...

-D

Thanks for the input guys.

Not really that keen on a band-aid fix tbk mid-life; love the car and don't plan on getting rid of it....

That's It D im the same, don't really want to risk it hay.

No idea if it could be an intakemanifold gasket kawa.

  • 2 weeks later...

Thanks for the input guys.

Not really that keen on a band-aid fix tbk mid-life; love the car and don't plan on getting rid of it....

That's It D im the same, don't really want to risk it hay.

No idea if it could be an intakemanifold gasket kawa.

iron tight is used in new diesel engines to seal of the sleeves that the pistons sit in so its more than a bandaid fix . i had a nissan patrol that overheated ten minutes after driving it due the a cracked head one bottle of irion tight and i drove that patrol around for another 6 yrs without pulling the head off and it was still going strong when i sold it .

ive used it on the night to fix head gaskets that blew when i raced turbo holden 6 at speedway and finished the season without pulling the head but anyway i was just offering something that may help till you could afford to pull the head or replace the motor .

cheers dean

Mid life..... Hope you didnt take my response as a personal stab or anything. Thanks for the idea but not real keen on doing that as ive got plenty of funds to fix this just working out the best economical way to do it properly....

So what parts will I need? Just a full VRS gasket kit?

Who has used a metal gasket with only machining the head and not the block?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...