Jump to content
SAU Community

Spray Tint

tridentt150v
 Share

Recommended Posts

tridentt150v Grand Master

tridentt150v

Posted
Posted

I've got a switch in my car that I want on, but its very very very bright red and is a bit of a pain at night. What do I use [besides a black texta] to dull it down?

I don't want to have to buy a $20 can of VHT for a 10 cent size switch with an inbuilt light so I'm looking for what others have done.

Link to comment
https://www.sau.com.au/forums/topic/372607-spray-tint/
Share on other sites
wilorichie Experienced

wilorichie

Posted
Posted

If its a really flat surface, you can use the same material as the touch-screen phone protectors. Colour it in with your perm pen and attach it on the plastic like you would with a phone. This way, no glue or anything is required and you can perm pen it as much as you like.

Link to comment
https://www.sau.com.au/forums/topic/372607-spray-tint/#findComment-5943400
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • Dose Pipe Sutututu
      remote oil cooler hose size, 8,10 or an12?

      By Dose Pipe Sutututu · Posted

      More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
    • Duncan
      remote oil cooler hose size, 8,10 or an12?

      By Duncan · Posted

      Dunno. I run -10 on the race car.
    • GD51LA
      remote oil cooler hose size, 8,10 or an12?

      By GD51LA · Posted

      street use or race track, what hose size and why? what factors change with the hose size options ?   see most comon is an10. when you see most oem external coolers are closer to an12? does high volume oil pump like nitto need an12 or 10 be just fine
    • SeanR32GtSt
      R32 only blows hot air

      By SeanR32GtSt · Posted

      The rod I was moving left and right you can see looking from the passenger side floor up into the center console.  IMG_8095.mov
×
×
  • Create New...