Jump to content
SAU Community

Recommended Posts

Hey Guys,

Currently in the process of respraying my DR30. I need to replace the door rubbers. Is anyone with fast able to give me the part number of both the drivers and passengers side for a DR30 Coupe.

I'll try my luck with Nissan. If its no cheaper, I'll just order through Jenesis.

Cheers,

Steve

Link to comment
https://www.sau.com.au/forums/topic/374298-door-seals/
Share on other sites

  • 3 weeks later...

the manager said no

but one of mate mates sells cars for nissan Launceston

and ones a mechanic there i think for 2 cartons of beer i may be able to have some thing happen

will see what i can score

c210 one plzz as well

Link to comment
https://www.sau.com.au/forums/topic/374298-door-seals/#findComment-5996059
Share on other sites

Im in the same boat, the triangle rubber thingy behind the mirror.

The munted one is at a place getting looked at, they say they may be able to reproduce them (although I guess checking teh nissan warehouse is easier!)

If you find some let me know

Link to comment
https://www.sau.com.au/forums/topic/374298-door-seals/#findComment-5996876
Share on other sites

  • 2 weeks later...

I missed the ones on yahoo :(

Does anyone have any rubbers they may of bought but never used and want to part with?

Also keen on mirror rubbers as well if anyone has some laying around.

Cheers,

Steve

Did you take my part numbers to your Nissan dealer?

Link to comment
https://www.sau.com.au/forums/topic/374298-door-seals/#findComment-6009896
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...