Jump to content
SAU Community

Recommended Posts

NEW DETAILS - PLEASE READ AGAIN

Read below for the new details.

MAS - Pre meet spot will be:

LocationTodd Road - Shell Service Station - Outbound

There are two ways you can get to this.

1) Via Todd Road itself

2) Via the Westgate freeway outbound, and use the off ramp into the Servo.

Time 3.00pm SHARP

Keep this thread clear of Bullsh(t posts please guys.

Only post if your are coming - or cant come... or have a question to ask.

Link to comment
https://www.sau.com.au/forums/topic/37452-mas-entrants-pre-meet-0204/
Share on other sites

Gibson car is OK for 4.00pm

They say move in time is for 5.00pm to get everyone there - if we can get any people there earlier (say 3.30pm) that would be great. Cabin are keen to move us in early as we are the biggest single group.

I will be @ MEC from about 3.00pm onwards to help co-ordinate. Will have the shirts with me. Might need someone to collect my car though...

BTW: Below are final proofs for shirts.

The stitched logo looks fantastic - shall do a run of men's polos after the show :(

Gibson car is OK for 4.00pm

They say move in time is for 5.00pm to get everyone there - if we can get any people there earlier (say 3.30pm) that would be great. Cabin are keen to move us in early as we are the biggest single group.

I will be @ MEC from about 3.00pm onwards to help co-ordinate. Will have the shirts with me. Might need someone to collect my car though...

BTW: Below are final proofs for shirts.

The stitched logo looks fantastic - shall do a run of men's polos after the show :(

whats the go with the stitched logo james? are they to go on the polos?

Well I was speaking to John from Exclusive and they have been told to get there at 4pm (they have 16 cars btw - not 6) so I think Cabin are damn confused fools for sending us an email saying 5pm - sending others emails saying 4pm and then telling you they want us early.

Ah FARKEN CABIN!

Ok, change of plans guys. New Arrival Time has been requested

Can we all meet at the Servo at 3pm ?

Cabin would now like us in at 3.30pm, or around that time.

Please post up if you can make it.

If not, that is ok... Just come when you can. But we want the majority or cars in at 3.30pm.

Thanks and sorry to stuff everyone around.

Cabin are a law un-to themselves.

Any problems Call me, dont PM me.

0408 33 77 07

-ash

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...