Jump to content
SAU Community

Recommended Posts

Hi Guys, Can anyone tell me were the 4 wheel drive Computer is located , Also i have a waste spark coil setup of my previous R32 , RB20DET Engine, I want to fit it to my RB25DET Neo Engine, Has anyone got the wiring setup for fitting to the NEO Engine, Do you have to use the rb20det Igniter ?, Thanks your help will be appreciated, Jamind

Link to comment
https://www.sau.com.au/forums/topic/375059-nissan-stagea-wgnc34-rs4-ser2-2000/
Share on other sites

I believe the 4wd ECU is under the centre console. That's one of the reasons it's so shallow.

Can't answer your second question, however. Is there a particular reason you're wanting to go wasted spark?

Atessa awd computer is in the boot left hand side wall in front of the opening compartment but before the strut tower. Makes it pretty hard to read the codes!!!!

Wasted spark for the RBs is history over here - new coils probably a better bet if you need them.

thanks for the help guys. My old rb20det engine had a miss, I pulled the coils out checked them and at lest 3 had the small cracks in them so they were leaking, So i bought a new waste spark with good leads, as the coil were 90 bucks each, any way at the same time i fitted a Apet ECU Chip to my computer, I started the engine checked the tune and took the car for a spin, Well f..... it freaked me how much power it had, The engine never missed a bet again, Well i sold the engine and keeped the waste spark. I am at the moment fitting a Stagea RS 4, RB25DET Neo to my car, i will run the coils that are in it but the first sing of a coil miss and the waste spark will be going in, So thats the reason thanks Guys

where do you get it from tho

i can't find anyone who even knows what it is

Try an electrical supplies shop or a marine supplies shop - you are just looking for a spray on insulator.

yeah start pulling shit off in the general direction of the inside of the back left quarter panel to find the ets ecu .its on the back of the piece of wall between the strut and the compartment (ish)

f**k what anyone says about wasted spark .they work good . if you wanna do it then do it . yes you will need an ignitor . one off any rb .follow the colours and wire the 6 signals to it then wire the ignitor to the coil like you did on the 20det . join up all the earths and the get some power where its needed and blah blah

It is a CRC product.

i've been to a few places that say they can get anything crc but all have a blank look when i tell them what its called

might have to keep looking, maybe i'll try jaycar for something next time in in there

i've been to a few places that say they can get anything crc but all have a blank look when i tell them what its called

might have to keep looking, maybe i'll try jaycar for something next time in in there

Here's a list of distributors:

http://crcind.com.au/crc-distributors-products

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...