Jump to content
SAU Community

Recommended Posts

Yeah, no way it will cause that kind of damage. I've used them on all my cars and never had any issues. Worst I've seen is a mates 32, which had paint lifting a little, hit it with the high pressure and blasted a chunk of paint off.

Paranoid OP should read the posts in the thread and take in the information. Seller was A. full of shit or B. didn't know what he was talking about. Almost every car detailer uses high pressure washers these days. The reason they don't dent is because water weighs bugger all and the impact is powerful, not torquey. Car panels flex anyway...and the ones that don't are too strong for water to cause a dent.

Case in point, buy a $100-$200 pressure washer from Bunnings, which is all you need for a car anyway...no need to even talk about industrial strength washers. Squirt your hand with it from 50cm away and discover that it has less strength to it than your garden hose when on full blast. I usually wash my panels off with the gun about 50-100cm away because that's where my nozzle attachment is most efficient at clearing suds from the car. At this distance it's softer than a shower. I've held it within 1cm before to remove bug stains and had no issues at all. It'll hurt your skin at this distance, won't hurt your paint unless you have underlying issues like cracked/chipped paint or rust beneath it...even then, the washing of the car with a sponge will do more damage than the pressure washer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...