Jump to content
SAU Community

Recommended Posts

hey guys, looking to get rid of my regoable track car.

Only selling due to working more hours and not being able to drive it as often as i should.

I have owned this car for almost 3 years and took it of the road due to losing my licence. car serviced every prac night with synthetic oil and filter, and plugs every 3 pracs as well as comp tested.

car has around 160 000 ish km on it speedo stopped working about 6 months ago, engine only has around 45 000 on it.

Mechanically the car has never given me any real trouble and anything else that has has been replaced.

engine:

s1 rb 25

splitfire coils

blitz injectors

z32 afm

tomei rising rate fpr

garrett 3037s, braided lines

turbosmart 48mm progate

6 boost exh mani

alloy rad

greddy cooler

oil cooler & relo kit, braided lines

fuel:

040 lift pump

044 external pump

alloy surge tank

driveline:

25 box

xtreme drift clutch

nismo 2 way 4.3 ratio

s14 rear cradle, solid offset bushes

solid diff bushes

suspension/handling:

33 brakes all round

project mu handbrake shoes

kazzama castor rods

custom shortened upper arms/nolathane bushes

cusco rear camber & toe arms

tien HA coilovers front & rear

front & rear strut braces

s14 lca's/boxed up

gtr rear swaybar

alloy steering bush

currently running stock 32 knuckles with s14 tie rods & ends

inside:

currently has stock seats but can come with Bride fixie on genuine Bride rail

deep dish s/wheel

boost guage

wheels:

front: work 17x9 +11 meshies with 90% ku36's

rear: work equip 18x9.5 +41 with shagged neutons

spares: 4x roh drift R's 18x8.5? + 38? all with 50% neutons

2x 17x8.5? + 28? equip's

2x 18x 8.5? + 30ish equip's, 1 cracked.

other:

3in dump/front pipe, screamer

3in straight through exh

bm44 brake master

ABS removed

wil also come with s14 steer rack with offset spacers which were used before when modded knucles were fitted until rhs one snapped, haha.

broken knuckles and a pair of stock 32 one's can be included as well.

cars 70% stripped but will come with stock seats and some trim etc

prob a few bits and pieces missing.

this car has legit rego with this engine but is currently un-rego'd due to using it as a track car, but can be re rego'd if needed.

car was dyno'd around last july on 98 pump with octane booster on 19psi and made 378kw and 580 Nm torque.

Price: 11000 neg

for more info or anything 0423387100, cheers jake. cars in sa

Attached thumbnail(s)

  • post-16822-13157108328381_thumb.jpg
  • post-16822-13157109141673_thumb.jpg
  • post-16822-13157109861489_thumb.jpg
  • post-16822-13157110700499_thumb.jpg
  • post-16822-13157111817925_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/376837-rb-25-r32/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...