Jump to content
SAU Community

N1 Oil Pump On Rb20

Tommyd32gtst

By Tommyd32gtst,
in Engines & Forced Induction

 Share

Recommended Posts

Tommyd32gtst Enthusiast

Tommyd32gtst

Posted
Posted

So I have recently purchased a r32gtst with a rebuilt bottom end and a n1 oil pump fitted. I was driving it the other day and the motor lost oil pressure and a death rattle was produced from the bottom end which I was suprising due to the very recent rebuild. I removed the engine and stripped down the bottom. Found number 1 main and big end bearings to be spun and mashed welded together and bearing further down the crank to be damaged also. I then removed to oil pump and inspected the modified drive collar and pump, the pump was fitted with silicon sealant and the gear housing plate of the pump has had insufficient clearance between the first journal of the crankshaft causing the crank to wear into the oil pump and metal filings through the engine causing bottom end failure. Has anyone seen this before or has any info? Such as is a gasket meant to be used to space the pump out or any other ideas?

Link to comment
https://www.sau.com.au/forums/topic/377444-n1-oil-pump-on-rb20/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.  
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • MBS206
      MAJOR FUEL ISSUES 25det neo r32

      By MBS206 · Posted

      Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...