Jump to content
SAU Community

Recommended Posts

Guys I wired in a new fuel pump into my 34 GTR and found it didnt work(and yes I got the wires correct and yes the pump works when tested elsewhere).

After that I resoldered the original fuel pump back in to check if it was a resistance thing etc, but that didnt work either, there is no voltage from the wires at the fuel pump

.

So for the moment I have just added a new relay in and got the power from the ignition circuit to switch the relay on and have the fuel pump direct battery voltage feed.

But I would really like to get the orignal circuit working. The fuel pump fuse is fine. I have checked all the fuses in the boot, near the drivers kick panel and under the near the jump start point in the engine bay. Are there any other fuses or can someone tell me where the fuel pump relay is actually located.

My understanding so far is that the ECU fuel pump relay signal puts out .6v (checked against another ecu in my car), from there I think it goes to an earth controller of some sort and then switches the relay on.

Im just shy of tracing wires, but if anyone can give me a heads up on how the circuit works i would be rather greatful.

Edited by sinistaGTR
Link to comment
https://www.sau.com.au/forums/topic/379292-r34-gtr-fuel-pump-electronics/
Share on other sites

well.... the fuel pump relay control on the ecu is actually contolled by the inputs the computer receives.

There is a fuel pump drive controller that turns the relay on and off.

Whan i turn the key on i get .6v for 3 secs so this indicates that the the signal is working fine (manual says approx .8v). Seems i may be having trouble with this drive pump controller.

Anyone know where this drive pump controller or the fuel pump relay is located.....im getting closer to this problem

Ok so quick update.... I took the battery terminals literally off then back on....and BAM 12v out the original fuel pump wires....so now have the 14v direct feed relay with the original fuel pump wiring being the swith for my relay....

random electronics lol

  • 1 year later...

bringing up an old thread, went to start the car this morning and it cranked fine but wouldnt kick in...

after abit of investifating we believe its probably the fuel pump as i was not getting any sound prior to cranking (power not getting to the pump??)

checked kick panel, front and rear fuse boxes, all looked good. tried unconnecting the battery and restarting with no luck..

i have a haltech platnium pro plug in that and i will take the laptop down tomorrow and try and see if anything pops up on the logging, and maybe rebooting the ecu (not sure if disconnecting the battery would do this anyways?)...

anyone have any ideas or tips, advice to solve the issues that seem very similar to the above.

any help will be greatly apppreciated.

Cheers,

Anthony

Relays are under the rear rt tail light. Make sure you are getting a pulse on that relay and there is 12v on it.

thanks for the tip mate, was wondering where they are.

im pretty hopeless when it comes to fixing things but will give that a shot tomorrow.

just under the internal boot side wall carpet? or further?

Relays are under the rear rt tail light. Make sure you are getting a pulse on that relay and there is 12v on it.

Hey mate,

Anything else i should check after doing the above test? what should i check if it is? or if its not etc?

thanks

u need to test the power at the fuel pump not the relay. and remember u need to test it while either cranking or wiyhing the first 3seconds or so while its supposed ti be priming once key on

Thanks mate, i will look into doing this on the weekend and go from there.

Cheers,

had another look at my issue this morning, and it appears that im not getting power to the relay or the fuel pump.

has anyone had these issues before? from research and looking at wiring diagrams etc it appears the fuel pump control module could be broken. may have to look at hard wiring the pump direct to the battery to fix this? does anyone know an easy way to test if that is 100% the problem, or would be the fact that the pump isnt getting power proof?

here is the wiring diagram i found for reference.

post-85191-0-58317400-1371967241_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...