Jump to content
SAU Community

Recommended Posts

Hey guys this has been bothering me for a while and i barely drive the car because of it. Its a 1990 gts4 with 200k on the clock. i get 250k's grandma driving and 200 with a bit of stick The computer has spat out NO error codes so im just going to replace every sensor with a brand new one. So far i have got on my list

O2 sensor- $98 (mechanic tested it and said its still working fine but bit of peace of mind)

AFM- $210 brand new. the car stalls quite often when slowing down and my idle is between 0-1200 when start up and then on some occasions it will just sit on 1000

TPS- Cant find. sometimes when i have been driving for a while the idle will stick at 1500. im assuming that is the TPS sticking ?

Coolant temp sender- $80 provided that rb26 ones fit. the needle always seems to be in the one spot

Thermostat- $50 piece of mind

Anything else anyone can think of. I have done fuel filter, fuel pump, tested regulator, changed plugs (all of them were black)

Cheers oh and if it helps im running BP ultimate.

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

It might be something as simple as the timing being out, whether the CAS is in the wrong position or the timing belt has skipped a tooth or 2, or perhaps whoever did the timing belt did it wrong.

I'd probably add getting those injectors ultrasonically cleaned if they are 200,000km old, I wouldn't bother with those fuel injector fuel additives.

If the plugs were black then it's probably running rich.

Get yourself a consult cable instead of blindly changing the coolant temp sensor, will also tell you if the O2 sensor is working, TPS, AFM etc.

Have you had the injectors cleaned? Have you cleaned the AAC valve? Have you cleaned / replaced the air filter?

Check the adjustment of the TPS. It also controls fuel cut-off during gear changes (when throttle snaps shut). (should be 0Ohms between pins 1&2 at "throttle closed", not 0 otherwise)

Could be a faulty temp sensor (different to the gauge sensor), which could be telling the ECU that the engine is still cold (should be 2.5kOhm when cold, 0.3kOhm at op temp).

Have you had the injectors cleaned? Have you cleaned the AAC valve? Have you cleaned / replaced the air filter?

No but will now also get them tested. maybe they are stuck open ?

Yes i have very little change.

Yes put a fully hektic pod filter on :)

The timing belt seems like a large possibility. it is 110000k old. i have the kit i just need to get my full RWC done and ill get it changed :) any way of checking with out pulling the engine to bits moodles

?

MY mods are as follows. Stock BOV vented into the intake, 3" stainless from the cat, EL oxy sensor im assumming, put an aftermarket fuel pump in, FMIC, RB25 turbo, Torque split controller, and a whole bunch of things that i believe wouldnt affect economy. stock boost as well

I can tell its running super rich because ill choke if i have a wiff near the exhaust pipe

i can tell you that the fuel sender is not out ( i wish it was ) as i ran it to empty got 175k out of the tank and put in 45 litres of ultimate which was 70 buckers :((((

I really appreciate the input guys. i hope to solve this problem and help lots of other skyline owners with shocking economy :D

Ok well that might be part of the problem. RB20 ECU's are alot more forgiving with non factory mods but because that turbo is pushing slightly more air then expected, your ecu might be adding to much fuel to compensate as a safety. Clean your AFM, replace your O2 sensor, check your filter, and do an ECU reset. This might help it

I'd still recommend Putiting it on a dyno to check AFR's at cruise and under load

OK update time

Spent two hours at the mechanics today learning sweet f a expect it runs rich as anything. Here is what was tested.

-Fuel pump and regulator, Very strong pressure and regulator was working fine.

-Coolant temp sender works but reads a little low apparantly.

-AFM is working in a operating range.

-Ground for the ecu and battery is good. though there was a piggyback wire connector on there for the sensors but nothing was on it ?

-Oxy sensor. Tried a another one his test tool and it was rich on idle and if the accellator was touched it would shoot to max. This pretty much did the same on my o2 sensor. he said mine looked reasonably new

-No error codes were present

-Injectors. Only tested the voltage and it seemed fine. he asked if they were aftermarket and i said i didnt think they had a red tab on them ?

-Throttle Position Sensor, He tested it and adjusted it.

So he reckons that there is a MAP sensor or a boost pressure sensor or something that maybe faulty. Can any one shed any light onto this ? He pretty much was clueless expect for that it was rich and that was the cause for bad economy. He reckons maybe there was a resistor of some sort maybe placed on the O2 loom. Can any one help or have any suggestions onto the causes of this ??

Any help is much appreciated. And Callen do you reckon a tune would be in order ? Can you tune for better economy

Unless you are doing highway miles, there is very little chance of the O2 sensor having any significant effect on your fuel economy.

What was the fuel pressure? Are you going to get the injectors flowed and cleaned?

fuel pressure was fine he tested it. he would clamp the hose and the pressure would go really high indicating a good pump. he said not to bother as they were working when it comes to injectors. they were working fine apparently and the problem is running rich

Ive been having the same problem of 250kms to a full tank recently. I would average it out to 60-70kms per quarter of a tank. My mechanic reset the AAC and reset the idle and chucked in some Iridium plugs. I filled the car up to full and so far I've done 50kms and the needle has not even dropped below the full line yet, maybe this is worth a try.

Hey mate just threw in some platinums not long ago, made no change :( Cheers for the advice though will try cleaning the aac again though. odd how plugs made that much difference, they must of been burnt out pretty well :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...