Jump to content
SAU Community

20,000Km Overdue Service On A Gtr- What Should I Do? Engine Flush?


Recommended Posts

Not changing the oil for that ammount of time is bad, but it's even worse when there is a turbocharger or 2 involved, it's quite common oil seals (rear main being one of them) have deteriorated and all that is holding those seals together is the sludge from the old oil.

If you do the timing belt, do the whole 100,000km service (belt, tensioner + idler pulley, both cam seals and the crank seal, water pump).

Since the previous owner didn't GAF, I think these 2 are important: brake and clutch fluid. While these should be done for peace of mind: front and rear diff, transfer case and gearbox too if it's hard to shift gears or crunches gears.

As for oil go with something very detergent heavy, it might even be worth getting some cheap oil in the correct weight (10w40) and using it to flush out the crap before putting a good oil in.

It's very lucky the engine hasn't spun a bearing actually.

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

Agreed with GTRNUR, dont flush it with an actual engine flush, (i have seen those things loosen up too much stuff and actually damage the engine) use the likes of gtx and do regular filter and oil changes i went anal and did 2 changes in 300 kms so clocked 100km after the first one, dropped it then did 200kms dropped it and kept doing 200km cycles untill it started to keep it's color took about 4 all up, i also split the filters to see is any crap came through and there was none, once i was happy i put in 300v, and change religouslty every 3500km funny thing is that the oil now keeps it nice clean colour for some time before going crappy. I would'nt stress too much about it in that oil quality these days is pretty good to the extent that some manufacturers are recommending 15k intervals on turbo charged cars. but thats no reason to sit on it . might even pay to take the rockers covers off 20 min job and have a look to see if there are any chips of shit built up in there, that is always a good indicator to the rest of the insides.

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

yes a r32 GTR for $5000 i think its cheap :)

ok so im going to change the oil with cheap 10w40 mineral oil but how many kms should i do before i change it again with either the same cheap oil or good royal purple?

thanks soo much for all your help!!

yes a r32 GTR for $5000 i think its cheap :)

ok so im going to change the oil with cheap 10w40 mineral oil but how many kms should i do before i change it again with either the same cheap oil or good royal purple?

thanks soo much for all your help!!

$5K gtr??? :cheers:

nice work man!

follow the steps that GTRNUR posted..

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

if it's a daily, change oil and filter this weekend, use it next week, drop the oil and filter that weekend and repeat for one more week.

then put good oil of your choice.

If not a daily, then replaice oil and filter, then put say 200km through it while driving as suggested above.. and drop it and repeat.

most of these cars weren't serviced properly in Japan anyway..

and you got it at a price where you could afford to go get an R34 GTR motor put in for like an extra $5-7K and still be in front.

5k gtr..... basic oil change not done in 20k..... no doubt every fluid will need doing sounds poorly maintained.... no doubt other issues will come up too....

Edited by rgr34

I'd suggest taking small steps with the car and don't buy anything expensive for it. For example: No synthetic oils.

You have a lot to establish before you go sinking any money into it. If you jump in with both feet trying to restore it to its former glory you could end up with a bottomless money pit very quickly. GTR's can be bottomless pits when they are in good condition, so imagine how bad a neglected one could be.

I'd suggest doing a hot compression test after you do the first oil change. This will give you some idea as to the health of the engine.

Oil pressure when its been running and is over 80 degrees will give you an idea of the bottom end condition. If it still drives ok, then drive it for the first week as is. Only once its proven itself a little would I then suggest changing the diff, gearbox, steering, transfer case and cooling system fluids.

I you jump in too quickly you might just be throwing money away on consumables you will be draining again when you start replacing the broken parts. If things start going wrong, and also if the shell is full of rust it would be worth considering wrecking the car and selling off the components. You will end up making your money back and then some.

Then go looking for another bargin.

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

id pretty well go with this but id change it 2k or so after you do the oil change with good oil... never hurts to put a fresh filter and oil through it

will a 15w40 mineral be ok??

Yes that will be fine. The main thing you are trying to acomplish is getting the built up garbage out of the engine.

So the pre-requisits to do this are:

No expensive oils unless you happen to own an oil field...

Use a new filter

Change every weekend or 200km as has been suggested for 2 cycles before switching back to synthetic

Dont rev it past 4500, and especially when cold keep the revs low.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...