Jump to content
SAU Community

20,000Km Overdue Service On A Gtr- What Should I Do? Engine Flush?


Recommended Posts

Not changing the oil for that ammount of time is bad, but it's even worse when there is a turbocharger or 2 involved, it's quite common oil seals (rear main being one of them) have deteriorated and all that is holding those seals together is the sludge from the old oil.

If you do the timing belt, do the whole 100,000km service (belt, tensioner + idler pulley, both cam seals and the crank seal, water pump).

Since the previous owner didn't GAF, I think these 2 are important: brake and clutch fluid. While these should be done for peace of mind: front and rear diff, transfer case and gearbox too if it's hard to shift gears or crunches gears.

As for oil go with something very detergent heavy, it might even be worth getting some cheap oil in the correct weight (10w40) and using it to flush out the crap before putting a good oil in.

It's very lucky the engine hasn't spun a bearing actually.

i have bought a GTR and the last owner says it hasnt been sericed in the last 20,000kms.

why on earth would you do that? unless it was extremely cheap..

id get it to a mechanic asap - oils / fluids etc the list goes on and on

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

Agreed with GTRNUR, dont flush it with an actual engine flush, (i have seen those things loosen up too much stuff and actually damage the engine) use the likes of gtx and do regular filter and oil changes i went anal and did 2 changes in 300 kms so clocked 100km after the first one, dropped it then did 200kms dropped it and kept doing 200km cycles untill it started to keep it's color took about 4 all up, i also split the filters to see is any crap came through and there was none, once i was happy i put in 300v, and change religouslty every 3500km funny thing is that the oil now keeps it nice clean colour for some time before going crappy. I would'nt stress too much about it in that oil quality these days is pretty good to the extent that some manufacturers are recommending 15k intervals on turbo charged cars. but thats no reason to sit on it . might even pay to take the rockers covers off 20 min job and have a look to see if there are any chips of shit built up in there, that is always a good indicator to the rest of the insides.

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

yes a r32 GTR for $5000 i think its cheap :)

ok so im going to change the oil with cheap 10w40 mineral oil but how many kms should i do before i change it again with either the same cheap oil or good royal purple?

thanks soo much for all your help!!

yes a r32 GTR for $5000 i think its cheap :)

ok so im going to change the oil with cheap 10w40 mineral oil but how many kms should i do before i change it again with either the same cheap oil or good royal purple?

thanks soo much for all your help!!

$5K gtr??? :cheers:

nice work man!

follow the steps that GTRNUR posted..

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

if it's a daily, change oil and filter this weekend, use it next week, drop the oil and filter that weekend and repeat for one more week.

then put good oil of your choice.

If not a daily, then replaice oil and filter, then put say 200km through it while driving as suggested above.. and drop it and repeat.

most of these cars weren't serviced properly in Japan anyway..

and you got it at a price where you could afford to go get an R34 GTR motor put in for like an extra $5-7K and still be in front.

5k gtr..... basic oil change not done in 20k..... no doubt every fluid will need doing sounds poorly maintained.... no doubt other issues will come up too....

Edited by rgr34

I'd suggest taking small steps with the car and don't buy anything expensive for it. For example: No synthetic oils.

You have a lot to establish before you go sinking any money into it. If you jump in with both feet trying to restore it to its former glory you could end up with a bottomless money pit very quickly. GTR's can be bottomless pits when they are in good condition, so imagine how bad a neglected one could be.

I'd suggest doing a hot compression test after you do the first oil change. This will give you some idea as to the health of the engine.

Oil pressure when its been running and is over 80 degrees will give you an idea of the bottom end condition. If it still drives ok, then drive it for the first week as is. Only once its proven itself a little would I then suggest changing the diff, gearbox, steering, transfer case and cooling system fluids.

I you jump in too quickly you might just be throwing money away on consumables you will be draining again when you start replacing the broken parts. If things start going wrong, and also if the shell is full of rust it would be worth considering wrecking the car and selling off the components. You will end up making your money back and then some.

Then go looking for another bargin.

I'd be going the other way with the oil.

Get a cheap 10w40 mineral oil, and change it every weekend for 2 weeks. While running the mineral oil don't drive the car even remotely hard. Just run it up to temp gently and keep the revs below 4500. Especially dont flog it when its cold. The idea is you want to filter as much crap out of the oil system as you can, not have it bypass the filter and get to your bearings. Higher revs mean high oil pressure which results in some oil bypassing the filter.

After your 2nd quick change, then fill it with royal purple/motul or some other high quality synthetic.

Everything else you change and do will be determined by the age of the car, its level of tune and how many k's are on the odometer. Timing belts are a 100,000k item as are the tensioners. It would make sense to change the diffs, gearbox, transfer case, steering fluids and coolant just so you can start a logbook for the car's servicing. Then do the next service of these area's at 1/2 the due km's.

And in the meantime fingers crossed that nothing has been damaged by the neglect.

id pretty well go with this but id change it 2k or so after you do the oil change with good oil... never hurts to put a fresh filter and oil through it

will a 15w40 mineral be ok??

Yes that will be fine. The main thing you are trying to acomplish is getting the built up garbage out of the engine.

So the pre-requisits to do this are:

No expensive oils unless you happen to own an oil field...

Use a new filter

Change every weekend or 200km as has been suggested for 2 cycles before switching back to synthetic

Dont rev it past 4500, and especially when cold keep the revs low.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...