Jump to content
SAU Community

R33 Intake, What Fuel Rail (R32/33/34) Gives The Most Injector Options?


Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

so do you guys have experience using that deatschwerks injectors? prices look good

just got my motor going again with some 1000cc side feed deatschwerks. had a little trouble with the latency but all sorted now and idle just as well as the nismo 555s they replaced. can drive around at low revs and idle like a stocker with enough fuel capacity for 800+hp

The 740s are only $50 more than the 550s, there is no reason to not get them is there? Only aiming for 250kw, maybe 300 in the future but I see 250 being plenty for quite some time.

Edited by Rolls

Hi Rolls i just did the injectors on my 34 gtt with stock rail and there are so many options.

Bosch ev14 injectors come in many sizes.

Sard

Nismo

Deatchwerks

Seimens

List goes on

All the ones i listed are bolt in. You dont need spacers or adaptor.

The only change needed is the plugs are different.

The bosch EV14 injectors come in sizes up to ID 1000 cc

You need to buy the 3/4 injectors for a neo. I just put them in my 34 with stock rail stock intake.

I paid 550ish for injectors 180ish to install and under half a hour to tune.

Plus RB20's use side feed injectors neo's use top feed

Edited by whitneybra

Rolls im in the same boat as you, im also looking for injectors that are regency friendly with the stock fuel rail, either going to go nismo or deatchwerks, im pretty sure the deatchwerks are just a highflowed stock injector? if anyone can confirm...so should be same colour etc.

Hi Rolls i just did the injectors on my 34 gtt with stock rail and there are so many options.

Bosch ev14 injectors come in many sizes.

Sard

Nismo

Deatchwerks

Seimens

List goes on

Nismo only come in 480cc which is too small imo, especially if you ever want to run E85.

The destschwerks are the only option that are truly direct fit. The rest require some form of modification to work.

Yeah going to buy the 740s, not cheap but I want to pass and want room to move in the future if I want to try E85 or aim for 280kw

Thanks for the help everyone!

Edited by Rolls

Yeah going to buy the 740s, not cheap but I want to pass and want room to move in the future if I want to try E85 or aim for 280kw

Thanks for the help everyone!

where are you purchasing them from mate?

Thanks everyone for correcting me about the rb20 injectors

www.tuffcarparts.com shoot these guys a email they sell lots and there was even a group buy here on SAU

Edited by whitneybra

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...