Jump to content
SAU Community

Recommended Posts

Hi all.... When u installed new clutch, do u need to do "run ins" or " soft drive / no trashing " for at least minimum 500k's before you can trash the clutch hard??..or doesnt matter??i will tell u the reason after why i ask once u guys answer the question first....

Well its one of those things where theres two sides, one say it is essential to wear it in for 500-1000 but other say pretty much you just thrash let it cool down thrash let it cool down a few times and its done. For example if its a track car you really cant afford to much around with driving around for 500km so a couple laps around the track thrash cool down and usually its fine. ive done both ways and have been fine but yeah personally I think its just a warranty precaution clutch companies use so as to guarantee since if you do drive it 500 to 1000 km easy it is certain the clutch will bed in but doing it the quick way if you do overheat it too much you can prematurely wear it so for a street car I would recomend to wear it in proplerly as its no rush but track car gota take the shortcut.

Usually?? Means its not necessarily and you dnt have to right? Well if thats the case i might have wasted my money and possibly will be getting a new clutch again as my new clutch has already been slipping .. Im sending it back to the company as they insist to investigate it further as To why its already slipping..clutch is actually on the way back to the company today, had a chance to see it before it was sent back And the shop owner told me its got all blue marking all over the clutch disk which mean heat.. He said its most likely i didnt do proper run ins.. He told me for atleast the first 500k to take it easy otherwise clutch would worn out easily.. Is this correct? And the owner advice me most likely the clutch company would not cover warranty on it if it finds the faults was me.. Which mean i just wasted alot of $$$!!! Is ther anything i can do about this?? I dnt want to buy another clutch if there is a way out.. Any suggestions as to what i can do if worst comes to worst?

We tell customers at work it's mandatory they take it easy for 1000-1500km. No excessive slipping, 4x4 work (some cases) or general hard driving, towing etc. etc.

Twice had incidents where KNOWN hoons (the type to kick and spin EVERY gear change, everywhere) come back a week later having clutch problems, and the clutch has been obviously abused. Obviously no warranty as soon as the clutch was sent back. One was a V6 VU ute, dual mass flywheel both times, quite expensive.

You'll be hard pressed to find a manufacturer who will give you warranty on a clutch that's been raped on it's first drive.

You don't take a fresh engine to the drags or a drift day and limiter bash...

You don't hang off the brake pedal from 300km/h down to 0 with new pads and rotors...

I dont like your chances with warranty as this is why they put the requirements to wear in. As i said if you try thrash it straight away but you do overheat it too much then yes you can damage it. What exactly did you do how did you drive? And how many kms has it been?

I dont like your chances with warranty as this is why they put the requirements to wear in. As i said if you try thrash it straight away but you do overheat it too much then yes you can damage it. What exactly did you do how did you drive? And how many kms has it been?

Well first things first, i hardly drive my car, i mean like 3x a week and i do get carried away sometimes... Since the clutch was in, i have done 1500 klms and i honestly i did gave it a hard time several times since.. Im no hoon tho..i just wanted how it would feel like with the new clutch in.. I guess im learning it the hard way.. Im pretty new with these sort of stuff..

When i put my new clutch in i was told to use it, not abuse it (ie, no clutch kicking, 6k launches etc).

I've been reasonably heavy footed on it since day 1 and have never had an issue.

Yeah but you have an awesome clutch

Clutch should be bed in - always.

Button clutches, not so much - they kinda find their own way if you know what I mean

If you do 6k launches and clutch kick on the first half a dozen drives then expect shit to be problematic.

In fact, clutch kick at all and you need to be slapped. I have never seen the use in clutch kicking, get more power

Clutch should be bed in - always.

I also go by this, clutch companys don't give warranty out to something that looks like its been abused. And going by the sound of yours having heat marks, i wouldn't hold my breathe they'll give you another one.

Was the flywheel machined during the new install? The material on the clutch plate(s) needs to bond with the flywheel smoothly in early life. Any hard launch or general abuse will result in bad surface match, thus leaving nasty crap on the flywheel that will eat your clutch faster and progressively get worse In the first few hundred kays, baby the car off the line. Do a bunch of hill starts, without sliding the clutch at all. Find the balance of the clutch so that you can get off the line without using throttle input until fully disengaged. Drive like this habituously and you will pride yourself on footwork.

WOT throttle is ok whilst not on the clutch. Any product worth its value will bite from the get go. My car performed full power runs on the chassis dyno with a 150km old clutch. Its simply how you make the clutch transfer the power whilst the car is stationary that will determine how long it will live. Have you ever tried to push a 1400 kg vehicle? Our drivetrains dont enjoy it any more than we do!! I found that my pedal feel changed overnight (about 700 km in) and am really happy with it.

Except one time when someone stole my car in broad daylight, drove it 50 metres, then brought it back...

b108a012.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...