Jump to content
SAU Community

Recommended Posts

hey guys,

today i started up the 1992 r32 gts-t, its stock with boost gauge and boost controller cat back exhaust, anyways, the car idles erratically and rev limits at around 2500rpm? how do i fix this asap? i've read elsewhere it could be the AFM or soemthing? any advice or a how to fix would be much appreciated.

also before this issue began my RPM gauge would go mental and turn completely past the redline, the revs don't change just the actual gauge itself, r these issues related??

Thanks

posted a video on youtube of the problem so so you can exactly what im talking about.

http://www.youtube.c...h?v=ZTDHzfr2h3I

Edited by Widesays

Definitely sounds like AFM. Unplug it and see if the car runs the same.

Try this:

http://www.skylinesa...your-rb26-afms/

car wont run without the afm matey but yeh it definetely sounds like it they do weird things depending on how low the voltage in them has gone just get a replacement one they are pretty cheap second hand for around 100 u should find one under. u havent tinkered with anything while the car has been laying there idle?

ok so heres an update, i started it up this morning and it was fine again? wtf, it first happened while i was going through a round about in 3rd gear, got out from the round about and the gear started limiting at 2500rpm so i pulled over and while the car was rolling (still running) i gave it a rev and it fixed itself, drove it home with no issue, then the next day went to start it and it was limiting as i drove up the block it hit 2.5k rpm and started like bunny hopping so took it home, left it, started it up in the arvo was fine, no issues. then as of now, this morning, is all good again??? could the wiring be short circuiting or is my afm dying?? as of right now i just drove it and its fine...only reason i ask about the wiring is because in the 1 - 2 weeks that ive owned the car, the window reg died (replaced it), the rpm gauge goes mental and last time i touched the heater i couldn't turn it off >< lol so i had to bash it then it turned off lol...any thoughts?

There is probably a bad solder joint inside the AFM. If you have a soldering iron you can crack it open and repair it using the How To on here somewhere. If not you will have to replace it.

car wont run without the afm matey but yeh it definetely sounds like it they do weird things depending on how low the voltage in them has gone just get a replacement one they are pretty cheap second hand for around 100 u should find one under. u havent tinkered with anything while the car has been laying there idle?

?? Mine starts with the AFM unpluged, but it idles at like 1300rpm and limited to 2500rpm. Have I got a vacumm leak or something?

if it won't run without the afm then you have another problem

r32's definitely will run without one, i drove about 5kms without one when my cooler pipe let go (exploded out of the car and into the bush, never saw that one again

?? Mine starts with the AFM unpluged, but it idles at like 1300rpm and limited to 2500rpm. Have I got a vacumm leak or something?

it will run like shit though thats what i m saying but yeh sounds like it is still the afm they are so cheap to buy just try one if its not then maybe a computer fault i got a spare one here i can give u for post if u wanna try it

it will run like shit though thats what i m saying but yeh sounds like it is still the afm they are so cheap to buy just try one if its not then maybe a computer fault i got a spare one here i can give u for post if u wanna try it

Mines fine just unplugged it to see what would happen. I'm from NZ anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...