Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

its danger is measured in its potential......yes any car is dangerous if misused. but skylines are designed to go fast, high acceleration etc. they're the atributes that make a car dangerous........

as a completly different example. a machinegun locked away where no one can get it, is still a dangerous weapon..........

mx5 good call

im getting a 89 r32 GTR for my first car cheap but the car wont be in too good condition when i get it ill have to do afew things to it then it will be just as quick as any other gtr

16k- 22k depending on condition of the car from www.j-spec.com.au tell craig RiceCooker sent you ^^

a machinegun locked away where no one can get it, is still a dangerous weapon..........

Yes, but it's still not dangerous until you get someone who wants to shoot people with it, or doesn't know how to use it. Yes, a skyline CAN be dangerous, but any car can be dangerous, its just stupid to say a skyline is BUILT to be dangerous. Skylines are built for speed, no doubt about it, but that doesn't make them dangerous till you start USING that power. If you get someone who never drives over say 30km/h in a Ferrari or something (yeah right) that's not very dangerous at all is it? but if that person starts doing 200km/h then it becomes dangerous. it all depends on the driver.

"its just stupid to say a skyline is BUILT to be dangerous. Skylines are built for speed"

Speed is what makes a car dangerous........i'd rather be hit by a barina doing top speed than a skyline. so if speed is what makes it dangerous and skylines are built for speed then skylines are built to be dangerous...........

makes sense

Not really dude, a skyline doing 140 and a barina doing 140 they both hurt.

The only reason I said that a skyline would be a bad car as first choice, is because you could reach 0-100 about 90 seconds faster then a barina, ie..

coming around a corner, hey man. fully sik bro check this stuff, floors it.. loses it.. sideways into a parked car.. can't see that happening in a barina.

and even if it did happen in the barina, what car would you rather repair, insurance wise.. a barina.. or a skyline... obvious, very obvious choice.

and yes, its possible a young guy could drive sensibly behind the wheel..

but if its his FIRST car.. and he's a young guy, in a skyline.. just, no.. don't risk it.

Patrick

Not trying to put you off mate, but if you think waiting until you have your P's is going to bring you all the experience necessary to safely and affordably own a Skyline; Please think again.

I don't think boys brains start thinking like mens until your around 25 years old, at which point you start to realise your not invincible and understand the consequences of poor decisions.

This is because you have had about 8 years driving shit boxes, learning from these mistakes and are still alive to tell the story.

By all means, be a car nut like the rest of us; but take on board other peoples advice from their experiences and don't learn it the hard way.

Good Luck again!

DRIFTO

I think any of the more experienced drivers will tell you that driving is something that takes years to master. Not a few weeks.

I use to think I was fast out on the circuit. Now I realise how slow I was.

An owner of a gun has a choice of:

(a) shoot any living animal he sees for fun

(B) Go to shooting ranges

This can be compared to an owner of a skyline:

(a) Speed and do idiotic things

(B) Obey the law and only speed in controlled areas (Drag strip)

As cars and guns vary, it doesnt mean that the owner must push it to the max. In my opinion an idiot with a pistol would be more dangerous than a police man with a rifle. The maximum output of the car/weapon could influence people to do stupid things but if the owner is mature he/she will know its not worth it. In the end I think it all comes down to the matuarity of the owner not the power under your foot.

- Patrick

1. Mine has been for me :)

2. Yeah they are pretty good but to ya research.

3. LOL if you want to be looking at the latest HSV’s and Tickford’s in ya mirror then a Skyline is for you.

4. Not hard but expensive, I have 3rd party thats it :P

5. Not much if anything!

Skylines are great first cars! ....r31 that is :P

to be honest, while they may be pretty old these days.. they are

a) reliable as rocks

B) parts are cheap and plentiful, and VL shared same engine

c) good on fuel economy.. around 10L/100km

d) bit of power, and gives you a taste of true RWD power without being too dangerous

e) Fair bit of room

f) gives you a taste of what owning a skyline is all about, before you get a turbo version.

g) pretty comfortable inside if you get a TI or GXE version

h) insurance is pretty cheap if you just go for 3rd party

i) lots of options for a car that age, power steering, elec mirrors, and elec windows and few extras if you get a TI

I used to own one before stepping up to the R33.. and in fact recently I went and bought another just as a runaround as I know how good they can be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...