Jump to content
SAU Community

Recommended Posts

Didn't know where else to put this, there isn't a standalone auto elec section. I'm just wondering what these two switches on my R33 are for.

First off is the broken one in the centre console, the icon on it has pretty much rubbed off but looks sort of like a car with lines beehind it and up and down arrows, I've tried to mock it up in paint the best I could. Has a brown PCB underneath it.

P1170096.jpg

P1170098.jpg

P1170099.jpg

button.png

Second one is an unlabeled one under the wiper control arm. It has a moulded section around it like it's supposed to be there but doesn't look like any of the other factory switches. It also doesn't have any writing on it, this may have worn off at some point but it doesn't look like it has copped a lot of use. Switching it doesn't seem to do anything that I've noticed.

P1170102.jpg

Any help would be greatly appreciated.

Cheers,

Michael

Link to comment
https://www.sau.com.au/forums/topic/382323-what-are-these-switches/
Share on other sites

I doubt at least that the one in the centre console is aftermarket, it is the exact same as the antenna switch except for the picture on it and if the other one is then why does it have a perfectly sized mounting point on the factory dash trim?

If you mean the rocker-type switch near where your left knee would be (below and to the right of the antenna switch in the last photo above), it might be an instrument dimmer switch, they're normally a roller type switch but the one on my new 34 is a rocker-type switch similar to this one. Doesn't seem to do anything on my car either though.

I think these were fitted for compliance in Australia as there needs to be an instrument dimmer control of some sort.

So is that McDonalds or Hungry Jacks that you have all over the place??? No wait....its Peri Peri Salt right?

I'm not sure what it is lol, probably a combination of the above

Switch is definitely a Nissan switch, I've traced it and the wiring looks like it's been chopped up at some point, it goes into a shiny black box under the dash which has a circuit board with NEC all over it, the wiring then goes up higher into the dash behind a whole lot of messy crap. So does anyone actually know what the switch is supposed to be for or what the NEC board is for?

P1170109.jpg

P1170108.jpg

P1170105.jpg

P1170111.jpg

Edited by Miguelone

I am with God Speed on switch 2, it fits so well because most switch holes are a uniform size, all cars must have adjustable dimming on the dash lights in Aus, but I am not sure how often it works in imports. The symbol on the first says traction control to me, car, skid marks, adjust up and down... But that seems a little far fetched....

  • 6 months later...

Wow that options sheet is interesting - so many options I never even knew Jap cars could have back then in the mid 90s, like auto dimming interior mirrors and front / rear PDC (parking radar). You'd usually expect this stuff on a lot of Euro cars.

Looks like you scored on finding the answer to your first switch! Although I never really understood parking aids such as these retractible poles, those coiled/sprung wire bits stuck to the lower corners of the car, or those rubber bump strips that people stick onto their bumpers. In almost every case, these parking aids look even more noticeable than if you actually hit something with your bumper at low speed, and almost as ugly. Although as yours was a genuine factory / dealer option it gives it some definite novelty value!

Mate if you think just that page is interesting check out the whole catalogue.

Series 1 options

http://www.r33gt-r.com/p/nissan-oem-catalog-1995-r33-skyline.html

Series 2 options

http://www.r33gt-r.com/p/nissan-oem-catalog-1996-r33-skyline.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...