Jump to content
SAU Community

Where Has My Boost Gone

nemini90

By nemini90,
in Engines & Forced Induction

 Share

Recommended Posts

nemini90 Enthusiast

nemini90

Posted
Posted

Hi guys i hope you can help me with my problem.

I have a 25/30 setup running a 35/40 turbo 20psi.

i had a cometic head gasket go on me about 5000km ago so i removed the haed and had it checked with no faults found.

I replaced this gasket with a nitto one and have had no problems till last weekend. I was up it for the rent and things were all going good till i got of the power and then about 1 min later i went to get back on it and the car made no boost. first thing i thought was that i had blown a cooler pipe but this was not the case so drove the car home which was about a 90 min drive in last sundays heat (car did not get hot).

when i got home checked turbo intercooler but no problems. i then removed radiator cap to find it had very slight milky warter. i then tested the head gasket with a die tester and it was inconclusive.

so im about to remove the head and check gasket by my biggest problem is where did all my boost go i have had a gasket blow befor and the car still made boost but now i cant even make 2 psi.could there be something more serious i a missing. i have no blow by and car still runs fine of boost. any help on what to look for would be great. i will be testing the head again for warping cracks and all so crack testing the top of the block. just so you know it is all forged,drysump,head drains,vct,all bolts are arp,car is/was making 450kw on pump

Any help would be great

Thanks Neal

Link to comment
https://www.sau.com.au/forums/topic/382891-where-has-my-boost-gone/
Share on other sites
SargeRX8 Grand Master

SargeRX8

Posted
Posted

Do a compression test, you will know if your headgasket is out. So when you flat foot it, no matter what rpm you are at, you don't make any boost? Can you hear the turbo spooling? if you can hear the turbo spooling, I would say the exhaust side is fine. IF the turbo does not sound as strong, loud and high pitched as it used to then you can assume that there is something wrong with the exhaust flow spinning the turbo. You can drop your exhaust, make sure you still have your exhaust wheel in tact. Damaged head gasket, you should be able to create some boost and see air in your water... I very much doubt that you will be losing ALL your boost through a blown gasket and all you are seeing is slightly milky coolant...

nemini90 Enthusiast

nemini90

Posted
  • Author
Posted

this is what has got me stumped the turbo is fine form what i can see wheels are intact no damage an with motor running at idle blows air out the turbo outlet.

i tried to get it to boost and reved it to 5500 under load with only 2 psi of boost to be made it sounded like it was spooling so could it be somthing more serious with the turbo.i dont run a show of valve

nemini90 Enthusiast

nemini90

Posted
  • Author
Posted

ok an update on my problems.

i have removed the cat and muffler both are 4 inch there are no blockages with these i have checked the wastegate which it a 50mm turbosmart that is ok

all vacume and boost lines are ok and i have remove inlet which is ok aswell.so now all i have left is the motor. i know your ment to do a compression test with the motor warm but since i have removed the inlet do you think it will be ok to do the test cold. i will have to wait a few days to do this i dont have a guage have to borrow a mates.

nemini90 Enthusiast

nemini90

Posted
  • Author
Posted

new update

i checked everything external of the motor it all came up good i have removed the head and sent it to my workshop ill wait to see what they have to say befor i pull the block down and have it tested

also i found a lot of oil in the water jackets

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...