Jump to content
SAU Community

Recommended Posts

Hi All,

I've got a totally stock R33 GTS-T and recently when pulling away from the lights the car struggled to accelerate past 2k RPM.

I'll have my foot flat on the throttle (and shows and sounds like the turbo is at full boost) but the revs go very very slowly above 2RPM and there's obviously no pull - no matter what gear i'm in.

I've changed my coilpacks about a month ago and the current problem doesn't seem like a misfire as such, it feels as though my foot is only slightly down on the gas (even though it's flat!!)

Is this the sign of a faulty AFM?? I don't think there's any smoke, but there's a bit of a odd smell when I pull up - the smell could, however, just be me haha

Any advice?

Link to comment
https://www.sau.com.au/forums/topic/383245-engine-stuggles-above-2000-rpm/
Share on other sites

It can be dodgy afm. 2krpm is the limp mode for the car. If it has a stock ECU stick a consult in it and see if has any issues. Do you get any engine check light? Could be many things causing this, boost leak, dodgy accelerator cable not opening the throttle, faulty afm, faulty injectors, misfire etc.

Thanks for the reply bud.

It does indeed have a stock ECU. The problem occurred once last week must seems permanent now :s

Every once in a while it shoots past 2000 RPM but 90% of the time she struggles. Very frustrating!

i had a similar problem. my stagea (r33 s2) occasionally wouldnt accelerate beyond 1500rpm. it was something to do with the fuel conservation mode the car goes into on idle - it was getting stuck in that mode! which was of course limiting fuel delivery and therefore power.

i fixed it by bypassing the dropping resistor and making the fuel pump go full pressure all the time

I did have a service last week (just changed engine oil, tranny oil and coolant) but she was ok for a day or two after that...

Also I had switched to Yellow Jacket coil packs about a month ago...

I haven't looked for any blockages as yet. Will do so tonight

Hello Dre678,

I can tell you it's not a faulty AFM as when they go bad the R33 ECU (At least in my car) won't let the car go past 4500 RPM and it's a hard jolt like hitting a rev limiter.

I would be more inclined to think it's related to boost at the moment as 2000 rpm is around when the stock turbo kicks in. Can you drive high RPM low boost? i.e. Very little throttle, Low gear. But really I know nothing more than it's not a faulty AFM.

You can try an ECU reset, it's completely harmless. (Check the forced induction quick reference guide)

Cheers

Check the throttle is opening fully when u press the pedal down.

Check TPS settings and base timing etc.

Is there any black smoke when it struggles to rev?

Check airfilter and catalytic converter

Thanks Aqeul and Jez,

I did try to keep the throttle slightly open in a low gear - it did creep past 3000 RPM but it didn't last for long as soon as the boost kicked in.

I haven't noticed any plooms of smoke when pulling away but obviously that's something I can miss.

I'll check out the cable tonight and might try the ECU reset too. I've got it booked in at a skyline shop tomorrow but obviously I'd rather solve it myself...

I don't know much about the throttle position sensor, but i'll do a search here.

Thanks again for the advice.

I did try to keep the throttle slightly open in a low gear - it did creep past 3000 RPM but it didn't last for long as soon as the boost kicked in.

Wind boost down to a dead stock level by running boost pressure straight to the actuator just to test.

Google will have lots of info on the throttle position sensor, it's worth checking your throttle body. Though if it can rev to redline in neutral very quickly with WOT though I would imagine it's not throttle body problem and more of a "tune" problem.

If you reset your ECU with a paper clip like in the how to on the sticky in the forced induction section it will give you self diagnostics by flashing the check engine light slowly "x" number of times and quickly "y" number of times to give you an error code "x,y" that can help you diagnose if it's a faulty sensor.

EDIT:

Resetting ECU: http://www.skylinesaustralia.com/forums/topic/2879-resestting-ecu/page__view__findpost__p__3262978

Error Codes: http://www.skylinesaustralia.com/forums/topic/2879-resestting-ecu/page__view__findpost__p__1699249

Wind boost down to a dead stock level by running boost pressure straight to the actuator just to test.

Google will have lots of info on the throttle position sensor, it's worth checking your throttle body. Though if it can rev to redline in neutral very quickly with WOT though I would imagine it's not throttle body problem and more of a "tune" problem.

If you reset your ECU with a paper clip like in the how to on the sticky in the forced induction section it will give you self diagnostics by flashing the check engine light slowly "x" number of times and quickly "y" number of times to give you an error code "x,y" that can help you diagnose if it's a faulty sensor.

EDIT:

Resetting ECU: http://www.skylinesa...ost__p__3262978

Error Codes: http://www.skylinesa...ost__p__1699249

Yep, in neutral there was no problem - the problem only occurred when in gear.

So I followed your advice and reset the ECU. It return a 55 code (which I read means all is ok) I went for a drive (a hard one) and it seemed to have done the trick.

I'll go for a drive tomorrow and i'll rack up plenty of km's over the weekend so here's hoping the problem has been solved! Thanks for all the advice!

  • 8 months later...

I had this problem today when I drove my car, I called my mechanic and he thinks it may have picked up bad fuel or had a blocked fuel filter. The problem seemed to go away after I put new fuel in it and cleaned the afm. I hope it's not planning on coming back!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...