Jump to content
SAU Community

Recommended Posts

So as some may know, I've been having some oil pressure issues lately. Last event it got worse though and now oil pressure is around 30psi on a cold start.

A few mates and I fitted a new oil pump yesterday, checked the pickup etc and all was well. But I've still got the same issue.

So are the clearances too big in my engine ? I don't know what else it could be.

I have a standard 25 with bigger turbo, standalone, oil cooler etc. Can an oil cooler and remote mount filter affect pressure?

I don't know where to look and I'm thinking it's time for a new engine.

Not going off a standard gauge btw, got an electirc aftermarket item that is pretty accurate (read 2psi at wakefield when lifters started tapping).

Anyone heard of shit like this before?

I'd really love to get the 33 to Wakefield Matsuri this weekend if I could.

Cheers guys!

Adam.

Edited by Run-It-Hard
Link to comment
https://www.sau.com.au/forums/topic/383546-low-oil-pressure-real-low/
Share on other sites

doesn't look like there is oil in the coolant, but I've probably run the car for 5 minutes max. Oil is milky looking in the oil cooler, and lines. So I'd presume if I were to drain it, it would all be milky.

Edited by Run-It-Hard

Well I'd say based on that u probably have blown a head gasket, I'd be draining the lot and inspecting it

Could well be ur oil pressure problem, so probably a new gasket as well as an engine and coolant flush...

Unless anyone has some other theories....

If u ran it long enough to open the thermostat I may well find oil in ur coolant

Edited by GTR_JOEY

So, managed to get the head off tonight. Suspisions confirmed, headgasket is a goner. Interesting reason towards it though.

I don't know how, or why it would happen. But the head and block have been elongated in two parts (both on the passenger side). I'm guessing snapped head bolts or what not. So it makes me think why the head has been off in the first place. The piston tops look amazingly clean for a suspected 140k engine ... hmm.

Anyway, so the holes were elongated and a inner ring was placed in there to fill the new OD. But whoever has fitted this has also elongated the head gasket to suit. The photo below is probably where it failed, as it's right next to the water/oil jackets. So yeah as soon as we pulled the head gasket off and touched the enlongated part, the copper washer built into the gasket fell out.

28l83kw.jpg

So the plan of attack is to get another pair of inner rings in the same dimensions, cut two down to suit the block and leave the current two in the head. That way it'll still bolt together without needing to chop up the head gasket.

Thanks for all your help Joey, legend!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...