Jump to content
SAU Community

Recommended Posts

Hi all,

Thank you for taking the time to read my question.

First of all i'll tell you a bit about my build.

I have a Autech HR31 Skyline setup for drift.

And now have come to the end of the build regarding engine and head wise, and am seeking assistance on which computer i should choose to run this setup.

It is a R33 RB26 head and RB30 block.

i'm thinking D-Jetro, but a bit lost as to what to choose.

Any advice much appreciated.

Also i need a loom???

post-36075-0-88596800-1321796570_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/383580-computer-advice-for-r33-gtr/
Share on other sites

Talk to your tuner and ask them.

this. no point walking into the workshop you want to tune it and handing them an ecu they've never seen before. if you plan on having a certain workshop do the tune then use the one they recommend. even if it isn't the best ecu on the market, having them tune something they know will give better results than getting them to tune an ecu with all the bells and whistles that don't end up getting used because either they don't know that it has them, or they simply can't set them up properly.

Yes you could do that, but no doubt any good quality ECU is tuned by a quality workshop.

Its cool now, i have been out of the scene for a while and contacted my engine builder, funny enough is the distributor for the ViPec V88 so thats what i'll be running.

but cheers for the input.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...