Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Also selling my 888cc siemens injectors low impedance to suit gtr rb26 after $400 specs below

These injectors flow 86 lbs/hr at 43.5 PSI ( 3 BAR )

FEATURES:

  • Genuine, reliable Siemens Injectors
  • Excellent response characteristics
  • Robust Design
  • Low Impedance

Specifications:

  • Coil Resistance: 2.35 Ohms / Low Impedance / Low-Z (Peak/Hold driver circuit required)
  • Static Flow Rate @ 43.5PSI ( 300kPa ) w/Gas: 86.2 lb/hr = 888 cc/min = 652.2 g/min
  • Connector: Bosch EV1
  • Spray Pattern: Pencil

img0040cg.jpg

Uploaded with ImageShack.us

img0041wc.jpg

Uploaded with ImageShack.us

img0042bo.jpg

Uploaded with ImageShack.us

Edited by ATLRGE

Hi mate i'm located on brisbanes southside near browns plains.

Un sure if they are z32 afm's but they looked bigger then my mates ones on his gtr so unsure. Unless you have part number for them i can check it out. They work fine only removed due to 15k of mod enhacements

Passenger side seat $150

Rb26 standard fuel rail $10

R26 mines pod adaptors running z32 afm's with blitz filters i think $150

R32 gtr dash board slight lifting. $150

R32 gtr lower steering column cover $30

R32 gtr Front passenger side gaurds $150

R32 gtr doors less switches and mirrors $120 each

R32 gtr boot interior lining rear over boot latch $30

R32 gtr boot lining pass side $30

R32 gtr front windscreen gutter tray no cracks $50

R32 gtr stock intercooled $100

R32 gtr centre console $80

R32 gtr gear surround plastic with 2 screw holes on pass side with no boot $50

R32 gloove box $60

R32 gtr driverside kick panel $20

R32 gtr plastic sill covers $30 each

R32 gtr interior light $20

Ame wheels to suit gtr with 215/45/17 tyres that are 80% tread $450

Hey mate pretty keen to come look at the boot interior panel and what ever else catches my eye lol.......when's a good time/day......I'm on the GC so guessing about a 45min trip up?

Hi mate,im looking for the drivers side plastic inner guard piece that covers the standard blow off valves,also the brake duct that bolts to it.Any luck?cheers Matt

Paid for one of the window rubbers and got sent the wrong side, contacted ATLRGE back and he said to keep it and will send the other one the next day express. That was over a week ago, have been constantly trying to contact him but no replys. BUYERS BEWARE!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...