Jump to content
SAU Community

Recommended Posts

Hey all,

I did a bit of a search but not exactly sure which terms to use so didn't find anything of much use.

I'm looking for something to protect all my vacuum/air-con/similar hoses from heat; I found over the weekend that a lot of my hoses on the exhaust side of the engine bay have gone hard and many are cracked. The ones on my boost controller solenoid in particular were completely shot and that is only about a year old. Short of using fire sleeve, what do people generally use to protect their hoses? Does the silver wrap from factory on the heater hoses actually do much, it doesn't look like it would be very effective?

Any suggestions would be well appreciated,

Cheers,

Martin.

Edited by Hanaldo
Link to comment
https://www.sau.com.au/forums/topic/383700-hose-heat-protection/
Share on other sites

I bought some silver reflective stuff off Go Gear, which will work fine for anything not too close to the turbo. But it is a wrap rather than a sleeve.

Similar to this

http://www.heatshieldproducts.com/productdetail/tapes-and-fasteners/thermaflect-tape/69/22

I bought some silver reflective stuff off Go Gear, which will work fine for anything not too close to the turbo. But it is a wrap rather than a sleeve.

Similar to this

http://www.heatshiel...lect-tape/69/22

I've got some of that stuff lying around, I used it as an outside layer on heatshields, but it seems an arduous task wrapping little vacuum hoses with it... Was hoping someone may have found something maybe like conduit that could quite easily go around the hoses.

A lot of these hoses are quite close to the turbo as well, I'd like to reroute as many as I can to keep them as far away as possible, but some of them it's just unavoidable, eg. wastegate lines, boost controller lines, etc. etc.

the problem with any of those heat wraps, conduits, shields, what ever is the heat from your turbo and dump etc is extreme and still melts the plastic from the wire over time..

without needing to drill any holes I was able reroute all the wires that ran down that side, out into the guard, up near the windscreen ( runs between inner guard and guard liner ) and back into the engine bay near the headlight,..

Problem solved :thumbsup:

the problem with any of those heat wraps, conduits, shields, what ever is the heat from your turbo and dump etc is extreme and still melts the plastic from the wire over time..

without needing to drill any holes I was able reroute all the wires that ran down that side, out into the guard, up near the windscreen ( runs between inner guard and guard liner ) and back into the engine bay near the headlight,..

Problem solved :thumbsup:

Yeh works for wires, but not the vacuum hoses or heater lines. The heat from my turbo is destroying all the rubber hoses on that side, and in the instance of the wastegate/boost controller lines, that could cause some serious problems if I don't catch them in time...

one of the sites i worked at up north used to cut the factory sleeving off injector harnesses on new engines before fitment and used a fibreglass sleeve simular to the red sleeving you see on peoples oil drains. was about half inch diamter and thinner than the red stuff but was effective. tooks years or so of contant 24/7 operations to make the wires hard and brittle compared to factory. i have put aside 10m or so as i rewire mine in the next month or so. i have it in black and yellow. will have a look for part number and price if your keen. :thumbsup:

would heat wrap work?

Possibly, but again it sort of seems a bit more effort than it's worth. I'm talking about 4-6mm hoses, so to wrap all of these with something like exhaust wrap (I assume that's what you mean by heat wrap?) or heat reflective tape would be quite a job.

I did find these two products on the website that Paul posted:

http://www.heatshieldproducts.com/productdetail/heat-shield-sleeves/thermaflect-sleeve-hook-and-loop/61/44

http://www.heatshieldproducts.com/productdetail/heat-shield-sleeves/hp-hose-sleeve/59/44

Those look like what I was hoping for, don't suppose anyone has any experience with these or similar products??

hey mate ive got my ass hanging at work so havent been able to upload photos. internal diamter is 10mm and costs $4 a metre. will try get photo or 2 up tonight

You can get this stuff? I need some for oil/water lines and boost lines around the turbo.. $4/m is quite acceptable!

oh the farken issues ive had trying to get these photos uploaded, if it wasnt the camera it was the computer usb then the computer in general etc.

the $4 a metre applies to the yellow one you see here. i havent found the part number of the black one yet but im guessing it will be simular. i also need to find out if it can be sold in smaller boxes but i think it can be bought by the cm

post-24655-0-02595500-1322305476_thumb.jpg

post-24655-0-19585000-1322305520_thumb.jpg

We've used a product called fire sleeve with good success.

red stuff? if so that stuff is the goods :thumbsup: but ive never seen it in a size that is practical for vacumn lines. but perfect for turbo oil lines etc :thumbsup:

Yeh that's it. Fire sleeve is also hugely expensive, I couldn't afford enough of it to cover everything that needs to be covered.

Thanks a lot for that Trev, I appreciate it thumbsup.gif Do you know what temperature that stuff is rated to??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Time to decide what’s more import, your power level or your budget because you’re going to struggle to keep both 
    • Our Southern Highlands Cruise is proudly registered with “R U OK?” Day.  Sometimes the best way to check in on your mates is by getting out for a drive together. Sharing a common passion like cars creates the perfect space to chat, connect, and support each other.  A simple “R U OK?” can make all the difference. Let's enjoy the drive, the company, and look out for one another. PLEASE WEAR YELLOW FOR “R U OK?” DAY Sunday 14th September 2025 9:30AM Meeting Crossroads Homemaker Centre 10:00AM Cruise Departure Via Old Hume Hwy 11:45AM Arrival at Mittagong RSL Club Meet Location: Crossroads Homemaker Centre Final Destination: Mittagong RSL Club *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yep, its been down for a while, as I understand it it will be back soon.
    • Yeah I also looked at Plazmaman, but, it ended up alot  cheaper getting black ones through EFI when you also added in the delivery cost
    • Nice shot! They look super clean. The roof rack delete on the black one is interesting. Would like to see more pictures from different angles. It's subtle but could make quite a difference to how the car looks in profile.
×
×
  • Create New...