Jump to content
SAU Community

R33 Gtr Vspec, With A Replaced Engine Issues

Skysthelimit
 Share

Recommended Posts

Skysthelimit Contributor

Skysthelimit

Posted
Posted

hi guys,

Hoping you can help me out with some queries.

2 months ago, my engine slipped a crank and resulted in me replacing the engine with another engine out of a R33 GTR Vspec with 70k.

I got the car back the other day, and I have found confusing temperature readings..

The Power FC shows the max temp it hits is 82 degrees, but on my dash, the temperature gauge it is high, hits the white line that is just before the max temp at the H. Coolant level seems fine, radiator fan spins. The oil temp seems fine from the stock gauge, sitting at around a third of the way to max. I have kept revs under 3.5k to keep things safe.

I am unsure which I should be trusting, whats the chances the Power FC is giving the wrong temp? I don't want to cook the engine that just got put in (I have it booked in at the end of the week).

Does the factory water temp gauge and the Power FC take temperature at different areas of the engine???

Also I have found the car to rev differently. When i release the clutch now, the revs drop to around 1700 rpm instead of down to idle. When stop at the lights, it might take about 20 seconds at 1700rpm before dropping down to the 950 idle. What can cause this, and is it something to worry about?

Thanks for any advice you can give me, much appreciated :thumbsup:

Skysthelimit Contributor

Skysthelimit

Posted
  • Author
Posted

ok thanks, I'd assume the same, but will try to check into it.

..also another thing I have noticed is..

on start up, I get a very high knock sensor reading from the power fc of around 200.

after that, the knock sensor is fine, reads under 35. I would like to assume, its just picking up some noise in that frequency from normal start up sounds.. but the old engine never picked up any abnormal high numbers on start up.. what's the possibility of this high reading meaning damage is being done? is it a concern?? :/

Cheers :)

r32line Mentor

r32line

Posted
Posted

Also I have found the car to rev differently. When i release the clutch now, the revs drop to around 1700 rpm instead of down to idle. When stop at the lights, it might take about 20 seconds at 1700rpm before dropping down to the 950 idle. What can cause this, and is it something to worry about?

Not a huge concern but the reason would be the way the Power FC has been programmed. A mate had a power FC put in his s15 and it did the exact same thing until he took it back and got it adjusted. Although I think in general, when you ahve a power FC and cold start the engine it tends to rev higher and for longer than a factory computer would. Talk to your tuner though.

As for the temperature issue I am not sure but playing it safe in the meantime like you said would be wise.

  • 2 weeks later...
Skysthelimit Contributor

Skysthelimit

Posted
  • Author
Posted

..ok.. further to the over heating issue..

So I had the thermostat looked at by the workshop that put the engine in. seemed ok.. they removed it and made sure it was opening properly..

but still overheated.

so today they replaced the temp sensor that sits where coolant comes out of the engine.

but the engine is still reading max over heating on the gauge. I even changed the dash cluster with a friend's, to see if it was a faulty gauge, and it reads at the very top of H now :/

The coolant does not run hot, its not bubbling like it should be if the reading is that high.

Can this mean coolant coming out of the engine is running hot, meaning some sort of engine problem??

I'm trying to now track down who sold the workshop the engine to see what they will have to say about it.

Any advice? Cheers

blind_elk Grand Master

blind_elk

Posted
Posted

There are 2 temp sensors just beside the thermostat housing - a single-pin sensor for the gauge in the dash, and a 2-pin sensor for the ECU. It sounds like your mechanic replaced the ECU sensor, you need to replace the gauge sensor.

The problem with the idle-down could be a dirty AAC valve - get it cleaned.

Skysthelimit Contributor

Skysthelimit

Posted
  • Author
Posted (edited)

thanks for the info blind_elk, but I was actually there when he changed the sensor, he changed the single pin one that goes the the dash gauge..

which is weird why a brand new sensor made the gauge read even higher :/

I'm thinking I will change the ecu sensor too, cause I'm worried that's not reading correctly to the ecu

Edited by Skysthelimit
blind_elk Grand Master

blind_elk

Posted
Posted

Then maybe the wire to the sensor is worn and earthing out (you can test a gauge / sensor malfunction by earthing the connection to the sensor - gauge will go full scale if it is working correctly). What does the gauge say when the engine is cold?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Was that deliberate?
    • Kinkstaah
      gtr hood match gt/gtt front fenders?

      By Kinkstaah · Posted

      You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • MBS206
      gtr hood match gt/gtt front fenders?

      By MBS206 · Posted

      After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • Kinkstaah
      gtr hood match gt/gtt front fenders?

      By Kinkstaah · Posted

      The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...