Jump to content
SAU Community

Rb25Det Neo Injectors

Josh...

By Josh...,
in Engines & Forced Induction

 Share

Recommended Posts

xclusiv Enthusiast

xclusiv

Posted
Posted

r34 and r33 both have 370cc injectors, i had my r33 at 12 psi with the same turbo by the sounds of it (3071 with the vg30 rear housing)

i had much the same mods as you and it had 200rwkw at 12 psi and was still running rich, so 14 psi should be ok i'd think

Rolls Grand Master

Rolls

Posted
Posted

I haven't heard of many people safely pushing more than 230kw with stock injectors, at 14psi hard to say as I don't know what turbo you have but you will probably be ok.

If you are running stock AFM you will be close to maxing that out as well.

Rolls Grand Master

Rolls

Posted
Posted (edited)

I just assumed he was getting a retune... waste of time if you use stock ecu imo.

edit: nistune is next, the car will run like an absolute dog without a retune, get a 10psi spring and leave it at that, even 10psi will have it coughing and spluttering though with the bigger turbo.

Edited by Rolls
gotRICE? Veteran

gotRICE?

Posted
Posted

Id say the fuel pump would run out before the injectors.

If your tune is conservative then you will be running very close to maxxing them out..

My stock turbo on 10psi with Walbro pump maxxed out the injectors easily when it was tune with a Link G4.

Legionnaire Collaborator

Legionnaire

Posted
Posted

It's kinda hard to say whether injectors should be fine or not without any specific info about the turbo. But my advice would be to get a package of Z32 AFM, injectors and fuel pump before bolting it all together. These three cost around 1000$ for a new AFM, a set of siemens 650cc's and a Deatschwerks pump.

Legionnaire Collaborator

Legionnaire

Posted
Posted

Yea, highflows may be okay, may be not, depends on how the've been modified, but almost always they're worse that injectors that come from factory with a designed flow. There are some good inexpensive offers for R34 injectors, starting from 50$/inj or there abouts. Search, there are some details about injectors suitable for NEO posted by forum members Simon-S14 and I think urtwhistle.

Legionnaire Collaborator

Legionnaire

Posted
Posted (edited)

Jecs used to be an in-house electronics manufacturer for Nissan, e.g. my AFM has "made by Jecs" badge on it, so it might be a highflowed set of stockies.

Do you have a link to the said set of injectors?

Edited by Legionnaire
dori34 Grand Master

dori34

Posted
Posted

simon uses siemen deka injectors, the 3/4 length 60lb injectors are a direct fit but will just need to rewire new plugs. you can get this from the states the cheapest.

im runing 600cc high flows and havent had any fuel or tune issues. currently making 245rwkw and soon to be 300.

speak to PJ on this forum, i got them down thru him.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...