Jump to content
SAU Community

M35 Bose Spare Wheel Well Sub

MOUTH
 Share

Recommended Posts

whitestag Community Regular

whitestag

Posted
Posted

Chris would proberbly know. From what I've seen playing with mine is they are powered so I jumper or something is needed on the non option deck to power it. Also haven't seen back of a non Bose radio so don't know if they got the space for the plug.

whitestag Community Regular

whitestag

Posted
Posted

Did a quick search as I knew I seen this before.

http://www.skylinesaustralia.com/forums/topic/278390-m35-factory-bose-sub-into-non-bose-stereo/page__fromsearch__1

zei20l Grand Master

zei20l

Posted
Posted

also, no, there is no wiring to the sub for the non-bose cars. but there is an amp built into the sub enclosure, so it wouldnt be difficult to work out the power wires and the audio input

zei20l Grand Master

zei20l

Posted
Posted

no mate i dont, im lacking the mounting screw for the sub to hold it and the spare wheel into the wheel well.

if i did, id have it hooked up already! i THINK it uses a speaker level input from the amps that are usually in the boot of the bose equipped models.

from an aftermarket head unit, i wouldnt imagine it would be too hard to wire up.

for $80 its worth taking the risk! lol

  • 2 weeks later...
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

as a FYI. these need at least a 6Vpp balanced signal into them to run properly.

if its still available can you take a measurement from the base to the top of it. I want to see if I can get it in the spare tyre well of my R32.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

Hi there, I am in Adelaide & also interested. I have sent you a PM.

you would be better off with the 6x9s that go in the rear shelf of yours..

manc01 Collaborator

manc01

Posted
Posted

you would be better off with the 6x9s that go in the rear shelf of yours..

Would you have any recommendations? While you are at it what about the fronts also? I know that it is subject to personal taste & budget but maybe a rough guide would interest a few people.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...