Jump to content
SAU Community

Recommended Posts

Now i know that the center locks arent, but would the double wishbone setup be "street legal" in a sense if you could get it engineered?

Yeah 100% it an be engineered. Suspension modifications can be engineered as long as they are designed and fabricated to a standard the engineer is happy with.

I've only done 1 GTR that's been engineered we made some minor changes to satisfy the engineer.

  • 3 weeks later...
  • 3 weeks later...

Troy I do still do those hicas rear ends, the design has changed slightly to make them easier to fabricate but essentially the same components.

Its been a while as weve been flooded with work before the Wakefield 300 and the begining of the motorsport year begins.

R33 Nacca duct completed

post-20349-0-71760900-1362429689_thumb.jpg

post-20349-0-89295000-1362429696_thumb.jpg

180sx cage thats being done

post-20349-0-27791300-1362429701_thumb.jpg

R32 GTR power steering resivour

post-20349-0-08178100-1362429708_thumb.jpg

AP upgrade

post-20349-0-43233200-1362429713_thumb.jpg

Intake and cooler pipes for a GTR

post-20349-0-06267700-1362429719_thumb.jpg

R33 M spec bumper splitter right back to fabricated mounts on the subframe

post-20349-0-62393300-1362429723_thumb.jpg

Last weekend we competed in the Wakefield 300 endurance race along side PIstore in an S15 that we built and prepared for production car racing.

The event went well before the poor little factory SR20 threw a rocker arm and ran on 3 cylinders 94 laps into the race.

Great event we will certainly return next year for another crack at it.

post-20349-0-32105400-1362887916_thumb.jpg

The way I rather do them is from the lower rear seat belt mounts

It's a case of remove the rear seat, bolt the harness bar down and do the track day.

Remove harness bar seat back in and back to normal.

Problem is those upper seat belt mounted ones create a dangerous lever when you pull on the belts.

They swing downwards in an arc allowing the belts to loosen.

The idea of those bars going down is to try and prevent that rotation. They just bend.

I don't have any photos of mine but they pull directly against the bolt holes with no rotating forces

I can see where you are coming from with that. How much would it be for the harness bar with both the back seat and top bolt mounts.

I like things to be secured properly when they are in so the more points I can mount it to the better.

I wouldnt mount a harness bar from the rear seat and upper front bolts, its way to over engineered for how simple a harness bar can be.

For an R33 a harness bar done from 4130 chromolly tube ready for you to remove the back seat and bolt in they are sold for $330inc gst.

Always up for some alloy engine bay work and subframe mods.

We are expecting our 1st baby to arrive early April so I haven't booked much in for next month which has made it easy to be picky with work.

Let me know when you want to get it done and ill accommodate it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...