Jump to content
SAU Community

Mates TX3 got noise EPA'd

Snowman

By Snowman,
in Victoria

 Share

Recommended Posts

Snowman Grand Master

Snowman

Posted
Posted

A mate of mine just got the nice EPA letter in the mail about his exhaust noise.

He's had the car for 4 years and its his first one (Im gob smacked about that as his car is FARKEN loud)

Anyways.... he has no idea where he might get a quieter loan exhaust from. Anyone have any suggestions?

cheers

:D

Link to comment
https://www.sau.com.au/forums/topic/38607-mates-tx3-got-noise-epad/
Share on other sites
jaybee Newbie

jaybee

Posted
Posted

Got the EPA check done on Friday at Exhaust City in Cheltenham and am very pleased with the result.

My car is right on the 90dB limit at 4875 rpm.

At 4000 rpm its 94dB and even louder on decelleration, but this doesnt matter.

Now I have a certificate to send in and it only cost me $27, which although is still a pain is not as bad as it could have been.

Paul from Exhaust city told me "You have the perfect exhaust system for your car".

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      NC MX5

      By Duncan · Posted

      sorted
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Thanks mate.
    • TurboTapin
      Crank Motorsports Front Axles

      By TurboTapin · Posted

      I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...