Jump to content
SAU Community

Recommended Posts

pitty those shocks are not really a "racing" style. i find the valving is nowhere. we had a customer with them in his r32.

pulled them out and put in his old tien superstreets and was 4 sec quicker at eastern creek... dont need the rain on your parade, but if you have the oportunity to swap them for the normal bc's id advise it.

sorry still in the newb stage here, but you guys havent had any problems using the bc br's in dailys, i was looking at getting them for my r34 in the 8/6 combo but after driving a friends silvia was wondering wether they'd be bone jarringly stiff like his were. thanks

im looking into getting aset in the next few weeks for my r32 gtr

but will most proberbly go with 6-4kg spring rates and then use the damper adjustment to fine tune them

i think the 8-6kg for sydney roads will be way too stiff...

I've got a set of 8/6 (v1's) on a 4dr 33 as a daily car, they aren't that bone jaring (and I drive about 45-50 mins ea way to work and back) on some of the shittiest roads Brisbane has to offer :).- sometimes have to dodge some of the larger bumps or potholes. I've got them adjusted to about 8 clicks off the softest setting

I've got a set of 8/6 (v1's) on a 4dr 33 as a daily car, they aren't that bone jaring (and I drive about 45-50 mins ea way to work and back) on some of the shittiest roads Brisbane has to offer :).- sometimes have to dodge some of the larger bumps or potholes. I've got them adjusted to about 8 clicks off the softest setting

  • 6 months later...

i got BC BR 's 32 gtst 8/6 combo and i find it to hard/harsh even on lowest damper settings. car is used for daily but gets driven hard at times.

i found it better with 2 up to 6 from softest dampening, so as not to be bouncing from bump to bump and i agree with harder on the front than the rear eg 4/3 on the dampners.

i have had these for around 1 year and i think with the softer springs will be one of the ultimate CHEAPER street setups.

i have put the 6kg rear springs to the front and am waiting for 5kg rear spring to arrive.

i was told they would not fit, but can CONFIRM they fit, only difference is the spring length by around 12mm longer in the rear springs.

i just wound down the bottom spring platforms as you would do normally.

i had shagged stock shocks on king lowed springs and locked at replacing shocks and found to be move affordable and performance buying bc racing coilovers, and after being defected with lowered king springs i wanted the height adjustable, so i could get it closer to legal . :)

from mij

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...