Jump to content
SAU Community

Recommended Posts

Hey guys

I Was just driving to civic and my controller is running unlimited boost for some reason. I haven't changed any setting or anything

It hits 14-15psi then jolts the whole car like the engine couldn't keep up. Checked the hoses to the controller and they all seem fine

Ideas?

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/388030-unlimited-boost/
Share on other sites

Turned the settings all the way down and it runs a solid 5-6psi now I just been WOTing it down the back streets and slowly setting my low setting in the controller back up

It's now pretty much got a flat 9psi programmed back into it.

Really weird because I didn't touch the settings at all and all of a sudden it started hitting 14psi on my low setting which was programmed at 8psi

Can anyone else hear their solenoide ticking away as they put their foot down? It sounds like someone clicking a pen really quick and can be heard in the car quite clear

Link to comment
https://www.sau.com.au/forums/topic/388030-unlimited-boost/#findComment-6185902
Share on other sites

You should be hearing the solenoid. That is weird and freaky bout the unlimited boost. Glad you got it sorted and didnt break anything!

Mine was giving me unlimited boost when i accidently mispiped it, had the wrong holes on the solenoid, but i was watching and paying attention cos was intending to set up the controller.

Link to comment
https://www.sau.com.au/forums/topic/388030-unlimited-boost/#findComment-6186517
Share on other sites

Haha its bloody scary!

I was just hitting Northbourne and gave it some and it just kept spooling

Then the whole car just went clunk and jolted

Girlfriend was like "WHAT THE FU$% DID YOU DO THAT!"

She thought I did it on purpose lol

I'm lucky that when I run with nothing connected to the actuator my ecu hits overboost cut :)

Link to comment
https://www.sau.com.au/forums/topic/388030-unlimited-boost/#findComment-6186656
Share on other sites

Yeah that's what I think they are way over priced

I will just get this nistune up and running then later when I throw more upgrades then it can handle I will sell and upgrade

People are running ~400rwkw with Nistune.

I don't think it has a limit for power or basic mods. It's when you wanna get complicated by plugging a wideband o2 sensor into it and stuff like that

Link to comment
https://www.sau.com.au/forums/topic/388030-unlimited-boost/#findComment-6187758
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...