Jump to content
SAU Community

Recommended Posts

I got a 040 fitted as low as I possibly could in my tank. Ran it to the warning light and it was still fine. That was because I had to not because I wanted to. I never let fuel drop below quater to half anyway.

Looks like you got it setup right. Should be much easier to slide in than the 040 with the modded bracket. f**k I hope I never have to go through that again. Its so hot inside the fuel tank and when it doesn't slide into place, the frustration kicks in.

I went to Clark rubber today and picked up some stuff to wrap it in and triple checked that it was fuel safe.

Just gotta find the nozzle that winds into the bottom of the 044 then I will be pretty much set

Going to make a walk through for everyone

  • 4 weeks later...

I might just go a walbro or nismo direct fit

Direct fit all the way. It is no fun when you have to trial fit the thing half a dozen times to make sure the cradle is seated all the way home, the pump/bracket/clamps aren't fouling on the tank, and the sock is as low as possible in the tank... I was happy with the end result but it took some work.

Unsure with the Nismo or Tomei pumps, but with the 044 there was a significant improvement from upgrading the power feed to the pump. Stock wiring just couldn't do the job.

Direct fit all the way. It is no fun when you have to trial fit the thing half a dozen times to make sure the cradle is seated all the way home, the pump/bracket/clamps aren't fouling on the tank, and the sock is as low as possible in the tank... I was happy with the end result but it took some work.

Unsure with the Nismo or Tomei pumps, but with the 044 there was a significant improvement from upgrading the power feed to the pump. Stock wiring just couldn't do the job.

had this issue with the bosch 040 which is suppose to be a intank version? had to remove/retry/refit 3 times.

ended up getting fuel cut issue below 1/2 - 1/4 tank even tho the pump was mounted as far down as possible, ended up getting rid of it and replaced with a walbro, and never have been happier, so much quieter too!

if i had the coin, i'd choose a nismo pump anyday.

Yeah I sadly miss judged the situation I was in.

Not a single place would sell me something that I could use to connect the sock to the pump without it breaking down in petrol.

The guy who is tuning my car is going to install a walbro for me at the same time so all good.

zomg. I'm sure I wrote an article about this awhile ago for a GTR: wait, here it is:

http://www.skylinesaustralia.com/forums/topic/111401-bosch-044-intank-r32-gtr/page__hl__gtr+044

Basically: the 044 is fine in fuel (mine's still in the tank and going strong); fitting isn't unreasonably hard for the flow; but there are reasonably-priced drop in replacements like nismo or tomei available now

that will get you close for similar money without all the fsck arsing around.

If you are considering Walbro and high HP you should check its flow at your required rail pressures like 65+psi (i.e. 38psi rail + 27+ psi boost) because you might be unpleasantly surprised at the falloff.

Cheers,

SW

I've got a 044 mounted in-tank and though it's a bit of a squeeze to get in, didn't really have any trouble at all.

The sock attachment can be brought from some company down here in Melbourne. Can't remember the name but if you give Sabbadin Automotive a call and let him know what it is you're after, he'll be able to sort you out :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Perfect, I'll get to it this winter then at the same time as I weld on my anti squat kit. 
    • Alright so my 32 only has one temperature no matter what degree you set it to. I’ve tried disconnecting the servo motor arm and moving it either direction and got no change. I’ve fixed the leak in my AC and re charged it and with it on and clutch engaged it still blows hot even though the low pressure pipe going to the firewall is ice cold. Both heater core hoses are hot while running as well. Diagnostic code showed 24 for intake air temperature sensor. Anybody got any ideas?
    • I said Garrett style. Not Garrett genuine. And something in the G30 550 range is what you want. Not those pokey little old fashioned T28 sized things. The intake ports in the head are small. There is little benefit in fattening up the runners and leaving ths actual ports small. Just run what you've got. And on the subject of Nistune vs Haltech etc..... You know you can control the transmission with decent standalone ECUs these days, right? No need to keep any of that old Nissan bullshit. Don't get me wrong - I use Nistune on my Neo. But it is a DET, so the number of bodges and workarounds I had to do to make it work in a chassis without ABS, TCS, etc, is quite small compared to the herniated arsehole you will have trying to make it work on a motor that doesn't have some of the things that the turbo ECU wants to see. Just easier to bite the bullet and go aftermarket outright.      
    • Hmm. Only when the f**king thing is actually working. Still can't find the leak. And that's with dye being put in the last 3 times!
×
×
  • Create New...