Jump to content
SAU Community

Recommended Posts

Coasting along at 60km/h on my way to work this morning, my car (R34GTT) starting running really rough and slowly dies to a stall. Now, this happened only a few weeks ago and turned out my battery was shagged - now have a new one and same thing basically has happened again at pretty much the same intersection. I knew it wasn't the battery as the car was turning over fine but there was a weird squeal from time to time. I let it sit for a bit trying to start it every few minutes - after about 10 mins it starts and I putt off to work.

Only have basic mods: 3.5in turbo back, FMIC, pod filter and I have had my 100k service done (around 80k's on the car) but I don't think the coil packs have been done. I know these are prone to fail but just want to see if this issue could be anything else? Do you think I will be able to make it home this afternoon?!

Link to comment
https://www.sau.com.au/forums/topic/389209-please-confirm-gurus/
Share on other sites

I wouldn't be so quick to assume coilpacks, in fact it could be something smaller like the AFM or CAS. If you think coilpacks though I think you should take them out, check for burn marks on them and if so, wrap some electrical tape around them and see if this changes anything.

well I am only speculating as it seems to be a common prob. To those that have had coilpacks fail on them - what are the symptoms?

When mine failed it was just one that failed and you get a permanent missfire as one coilpack shit itself... It happened on startup and i just replaced them on the spot with Splitfires.... Not the same as what you are describing?

BTW - Anthony had some splitfires for sale dirt cheap in the FS section (Guilt_toy)

When mine failed it was just one that failed and you get a permanent missfire as one coilpack shit itself... It happened on startup and i just replaced them on the spot with Splitfires.... Not the same as what you are describing?

BTW - Anthony had some splitfires for sale dirt cheap in the FS section (Guilt_toy)

Hmm, no definitely not what's happening to me mate. Spoke to my mechanic and he thinks AFM or one of the sensors, he is going to check for fault codes tomorrow morning. Better not be something major as I have just dropped a load getting the 100k service done early!

bit of an update - my mechanic didn't find any fault codes or anything abnormal, however suspected (along with a few others) that the symptoms suggested AFM or CAS. The car stalled on me again today but instead of just dying out of the blue it started shuddering under acceleration first then eventually slowed to a complete stall.

A mate flushed the AFM out with cleaner and also cleaned out the pod etc - seemed to be a bit of rubbish in there along with a half cracked AFM plug. Taped the plug up and I took it for a half hour drive with no issues so far....HOPING that's all it was but probs not that lucky :closedeyes: so brings me to my next questions - which AFM's fit R34? can I go straight to a Z32 or should I just go for a brand new OEM? cheers

Z32 will need a re-tune, Clint :)

Physically the same size as the RB25 AFM but with more resolution.

Perfect opportunity to get the car Nistuned although I think you'd struggle to find a mob competent enough to do it in Twmba. :P

I believe you could try asking your mates with R33s if they can swap AFMs with you for a bit to see if the problem goes away.

I'm not sure if RB25 Green (R33 series1) and Pink (R33 series2 and R34 Neo) labelled AFMs are the same but I'm confident the pink ones from the R33 are exactly the same as the R34.

Could also be the plug as you mentioned...be it cracked / loose / etc..

At your service.

Trolling SAU since 2007 ;)

Yea, try to get another AFM/plug to test. If problem re-emerges, you can move onto something else (think you already know this haha)

I would offer but my AFM/CAS/Coils/whateveryouneed does you no good :P

  • 3 weeks later...

May be completely unrelated. May be a lil bit related... I had a camry once. It had a dodgy voltage regulator in the alternator. This caused the alternator to slowly deny charge to the car. The battery light was always on (thought it wa faulty, lol). This then lead to a loss of power on the highway... spluttering... and finally, a stuck car. Battery was dead. as it wasn't charged.

But since you didn't mention a battery light, or anything of the sort. I'll assume it's not that. But have you ran a multi over your car yet? Just for kicks?

Yeah my mechanic speculated CAS originally but wouldn't that make it run dodgy more consistently or would it only be an issue for hot starts? It seems to be fairly erratic atm. Sometimes it will hot start fine, sometimes it will have a slight hesitation, other times I will have to crank it for a couple of minutes - let it sit for a few minutes - then try again.

Dion - haven't seen any battery lights etc, and I put a new batt in only a month or 2 ago so hopefully not an issue. Running a multimeter over it sounds like a good idea - any specific areas I should check?

Just to elaborate a bit. My car was hard to start hot and would itermittantly miss at times through out the rev range.

Also at times i would take off from the lights and the car would bog and crawl for 50 meters then take off.

I replaced the Afm (the old one was clean with good solder on the pins) This fixed the missfire and bogging down issue.

Was still hard to start and worse when hot.

I Bought a new CAS and fitted that, now starts perfect.

Pulled the old one apart to inspect. There was wear in the keyway, when spinning the shaft you could feel the rumble in the bearings and it was full of dust.

May be of some help

Just to elaborate a bit. My car was hard to start hot and would itermittantly miss at times through out the rev range.

Also at times i would take off from the lights and the car would bog and crawl for 50 meters then take off.

I replaced the Afm (the old one was clean with good solder on the pins) This fixed the missfire and bogging down issue.

Was still hard to start and worse when hot.

I Bought a new CAS and fitted that, now starts perfect.

Pulled the old one apart to inspect. There was wear in the keyway, when spinning the shaft you could feel the rumble in the bearings and it was full of dust.

May be of some help

yeah mate, I was having the bogging down issue too until I cleaned my AFM.

Not sure if this helps diagnose my issue further, but I notice the car seems to pop a lot more more between gear changes - especially when I am under it. I may just have to bite the bullet and get a new CAS, is it worth trying a second handy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
×
×
  • Create New...