Jump to content
SAU Community

Help Seating New Wheel Stud!

Harey
 Share

Recommended Posts

Harey Veteran

Harey

Posted
Posted

Hi Guys,

I am halfway through replacing a snapped wheel stud. I have the new wheel stud in the hole and am trying to pull it through so it sits level with the other ones. I have put some spacers/nuts in between the wheel nut and the hub to help pull it through.

However when I tighten the wheel nut the whole hub just rotates!?!?!?! What do I do??? Read heaps of threads and they all say just tighten the wheel nut to pull the stud through. But I cant get any force because the hub just rotates.

I am trying to get ready for a track day tomorrow so any help asap much appreciated!!!

Link to comment
https://www.sau.com.au/forums/topic/389365-help-seating-new-wheel-stud/
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted (edited)

If you haven't already; Put the brake rotor on, and the caliper. Get someone to stand on the brake while you pull the stud through. At a pinch you can use a bar wedged against the brake and into the base of the seat frame . Obviously engine on, so you get the benefit of the booster.

Don't forget to lube the thread when you're pulling it in; you don't want to gaul the thread before you get to use it.

Edited by Daleo
Daleo Grand Master

Daleo

Posted
Posted

If you were changing it on the rear, yes. You may also be able to use a rattle gun, so you can push against the stud instead of pulling down on it. Be careful with a rattle gun, though, very easy to strip the stud.

This^^^^

I wouldn't use a rattle gun; you just don't have enough feel when you're tightening. It shouldn't be that hard to pull the spline of a new stud into the hub anyway; if it is, you've probably measured wrong.thumbsup.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...