Jump to content
SAU Community

Recommended Posts

Sorry I cant make it either Richo.

Got a new Brake Master Cylinder put on today. A bigger, better, larger unit to suit the Brembo's. BM57. (Bigger than 1")

Instead of the BM50 for the Sumitomos (1")

Now I have braking issues - Again :(

Booked in again Wednesday to get it looked at.

Sin

Stocker should work fine with the Brembos. But then so should BM57, what's the issue?

The stocker became spongy when I had the New rotors and Brembo calipers put on. Pedders put the rear calipers on the wrong side therefore the bleed valve was opposite to where it shouldve been and air got stuck. :(. Took it back twice and they didnt work it out. Took it around the corner to ACT brakes and within 1 minute they told me the problem. So they put them on the right sides and up the right way bled, and all good.

Because I put the Bremo's on I bought the BM57 to suit. Today ACT Brakes put it on and I am back to spongy.

When the ehgine isnt on the brake peddel is hard. Turn the engine on and they go instantly spongy.So doesnt appear to be air trapped in system.

So anyway - back to ACT brakes on Wednesday. If they cant resolve within the day I'll get them to put the BM50 on. As it turned out to be very good.

I thought I'd get better stopping with the match of Brembo calipers and the BM57 like the Vspec I and II.

The bigger BM57 will give you slightly shorter pedal travel and a harder pedal so while the stocker will decrease harness and increase travel it shouldn't be excessive or spongy. The movement when you turn the engine on is it 'sponginess' or 'travel' because the booster is getting vacuum?

Edited by Scooby

The booster appears to get vacuum as it should but the sponginess is more than should be.

There should be a point where the pressure increases and then goes fairly hard as the brakes are applied

I dont get to the hard bit and the first half is soft like there is no pressure.

Any ideas ??

The other thing that annoys me is that every brake shop discounts bleeding the ABS without reason - Why is that?

It connects directly to the BMC, it has the capacity to trap air, it's higher than the calipers and higher than anything else in the brake system (except the BMC which is pretty much at the same level), it has bleed valves on top of it !

I'm not a brake specialist BUT i am mechanicaly minded and logical.

The booster appears to get vacuum as it should but the sponginess is more than should be.

There should be a point where the pressure increases and then goes fairly hard as the brakes are applied

I dont get to the hard bit and the first half is soft like there is no pressure.

Any ideas ??

The other thing that annoys me is that every brake shop discounts bleeding the ABS without reason - Why is that?

It connects directly to the BMC, it has the capacity to trap air, it's higher than the calipers and higher than anything else in the brake system (except the BMC which is pretty much at the same level), it has bleed valves on top of it !

I'm not a brake specialist BUT i am mechanicaly minded and logical.

Faulty valve or torn diaphragm?

  • 1 month later...

So how many of you keen to go for a drive this comming weekend ??

Thinking of grabbing a big breaky in Cooma (1hr away) then maybe a short stop at Jindy for photo op and then lunch at Charlottes private parts.

Maybe even cold drinks when we get back

Following weekend is Wheels @ old parly house.

I won't do it this weekend, doing Motorkhana on Sunday.

But I was close to driving out that way last weekend (Canberra long weekend) until the R32 engine died while out and about. Anyway that got me wondering if any of the roads up there had been closed from the recent rain? A majority of the fun roads were closed and we found out for good reason.

Ahh man would be keen! But I'm getting my St pats day celebrations on.. come on St pat's day on a Saturday! Its like a lunar eclipse...

But next few weekends ill be available. Ill also be getting new rims which will need a photo shoot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...