Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Still cant figure out how to link larger pics?

Get a flickr account (least compression on the web). It's free.

From the URL that i can see you are uploading straight to SAU and SAU is hosting it. Link from your flickr account and you can choose your sizes :)

Get a flickr account (least compression on the web). It's free.

From the URL that i can see you are uploading straight to SAU and SAU is hosting it. Link from your flickr account and you can choose your sizes :)

I do have Flickr.

Tried this and it didn't work before.

Also tried Photobucket, and that didn't work.

I used to be able to, but I think I've lost the knack.

I like the shot above, wish there was more light on the exhaust/rear part of the car. Not much, just a little bit more :)

Luke_GTR - When you go to flickr, click on a photo --> Click on Share --> Click on "Grab the HTML/BBCode" --> Make sure HTML checkbox is ticked --> You can choose what size you want. Original size will be the huge version, so choose something smaller.

Just home from the honeymoon & going through the photos so probably first of a few I'll chuck up.

Grand Canyon, 2 degrees C & snowing...

HDR_4315_2.jpg

HDR, little frame movement in foreground but not bad for hand held & windy conditions.

This is an amazing shot!!! I was nearby there in September but my partner and i never ended up going to see it, didn't have time.

This is an amazing shot!!! I was nearby there in September but my partner and i never ended up going to see it, didn't have time.

Cheers, yeah we almost missed it too but decided to fly out from vegas. So happy we stumped up the extra cash!

Been having a play after work, couple more of the canyon. Really happy with these but my post editing only goes so far, might hit up some of the boys at work to help then get a couple printed.

First is of snow storm rolling in, next couple are after its cleared.

HDR_4232_2.jpg

HDR_4335_2.jpg

HDR_4326_2.jpg

Couple more I've toyed with too, these aren't hdr's though.

Liberty Island

IMGP4796_2.jpg

Statue of Liberty

IMGP4844_2.jpg

World Trade Center development at night

IMGP4850_2.jpg

Empire from Rockerfeller

IMGP5117_2.jpg

Display from American Museum of Natural History

IMGP4912_2.jpg

Nice to have something to share that isn't my z32 so sorry guys I'm spamming this thread!

cheers, Tim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...