Jump to content
SAU Community

Recommended Posts

Hi all.

Having a problem recently. Whenever the fuel gauge needle points to the middle of the last quarter of the gauge ( almost to the empty mark, but no light on), the fuel system seems to act up and the car would start sputtering like it's dying out. Happened once when I was pulling into the servo and another time today when I was stopping on a downslope at my workplace. The car decided to cut out and wouldn't start until I rolled it down to level ground before it fired up normally. Both times had my fuel gauge pointing close to empty. But this doesn't happen at all whenever the needle points to anywhere above the quarter mark. Hence comes my conclusion that the fuel pump can't seem to be drawing fuel whenever there's too little fuel. But I've had this much fuel left in the tank many times before and never had this happen before until recently. Does this mean a dying fuel pump or can anyone offer any advice on this? Tried the search button but not sure if this is similar to others' problems or not.

Link to comment
https://www.sau.com.au/forums/topic/390424-fuel-pump-on-its-way-out/
Share on other sites

Do you know if the factory fuel pump has been replaced with a Bosch or Walbro fuel pump? If so they don't take too kindly to the fuel levels reaching 1/4 left (to do with the physical mounting position inside the tank and the sock attached to the bottom of the pump).

That said, a fuel pump has to work harder when the tank is nearly empty vs a full tank.

yeah it sounds like it has an aftermarket fuel pump that is sitting up a bit high. having said that, if done well, an aftermarket pump should be able to still operate until the fuel light comes on.

other possibility is that his fuel gauge isn't accurate and is reading higher than what it should, but he could rule that out by simply taking note of how many litres he puts in when the issue occurs. but my money is still on it being an aftermarket pump

If it is indeed a stock fuel pump, the pump may not be the problem.

I have had two fuel pumps fail.

I had no warning, it didn't gradually 'lean' out.

The car will simply stall and die. Luckily for me both times were on the track and not the road!!

Edited by r33cruiser

Not sure if the pump is stock or not. But thanks all for the feedback. Asked the old man about this and he reckons that it's just a dirty fuel filter getting constantly blocked up by sludge in the tank when the fuel level is low. Might change the filter anyway as it looks like it hasn't been changed since the car rolled out from the factory. But can anyone confirm this?

mad082: When this happened at the servo, I put in around 56-57 litres, which makes about 8-9 litres left. It didn't happen again after that until it reached about the same level and I topped up about the same amount. Odd that it should happen at 9 litres when the missu's civic had only 5 litres left once and didn't have anything happen to it other than leaning out slightly.

Edited by LNah

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...