Jump to content
SAU Community

Major Issue, Help, Leak?

mikeyR33-T

By mikeyR33-T,
in Engines & Forced Induction

 Share

Recommended Posts

mikeyR33-T Collaborator

mikeyR33-T

Posted
Posted (edited)

REPOST - as i posted this at like midnight and realised no1 was on, and need definite answer before I waste money on the gasket set?

Hi, before anyone jumps in, I have read about 20 different posts in relation to this and none of them are exactly the same as mine

Started the car today, from first crank it had a persistant tick/click sound like tick tick tick tick and even with throttle it was there and it increase in volume & speed as the throttle increased (using the throttle cable in the engine bay)(R33 S1 auto, stock turbo, stock inj, stock engine)

I waited a good 5mins before driving the car, opened the hood and my ear was directed towards the top right hand side of the engine bay between the turbo and the wall/flywheel. couldnt exactly pin point but it was louder right there in that corner.

first I thought it would go away but I had some business to take care of, SO i drove the car 45mins and the click/ticking continued, was faint when driving unless I went pass a car or in a tunnel, but it was still making the noise whilst I was driving the whole time, as well as on Idle parked.

At first I thought it was the lifters but lifters usually sound deeper, then after reading i am thinking it may be a big leak in the exhaust/turbo gaskets causing the noise, as it increased with throttle as if it was controlled by the air passing thru the exhaust.

can anyone shed some light at tell me if its likely to be a leak as it made the noise in Idle and driving, no matter what rpm or speed I did. and its coming from the right side of the engine near the turbo/exhaust!

any advice would be appreciated, its possible gasket or bolts have snapped and caused a leak??????

please help, as I just got myself Z32+nistune today ready to be tuned, but cant do a tune till I sort this out! hoping its just a leak and not lifters! ( it made this noise before I changed ECUs)

thanks heaps

Edited by mikeyR33-T
Link to comment
https://www.sau.com.au/forums/topic/390800-major-issue-help-leak/
Share on other sites
SargeRX8 Grand Master

SargeRX8

Posted
Posted

Get a, piece of hose and stick one end in your ear and the other around the engine bay to pin point the noise. My car ticks, its my injectors. My old car had an exhaust leak and I'll tell you what, it didn't sound like a tick, more like a screech.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...