Jump to content
SAU Community

Recommended Posts

As topic states i am after a long motor that has good compression and very well looked after. Doesn't have to have all bolt ons.

I am located in melbourne, i rather local thanks guys

Link to comment
https://www.sau.com.au/forums/topic/391334-wtb-rb26dett-long-motor/
Share on other sites

  • 2 weeks later...

i've got a built RB26DETT, forged rods and pistons, 2860-5 turbo's, siemen's 660cc injectors, adjustable cam gear's, new waterpump, 13'000 km since build only running 17.5psi, very well maintained, PM me if your intersted, recepits for all work if i can get them restored at the photo place in town as they're fairly faded.

i'm willing to sell with or without turbo's, exhaust manifold, intake plenum and alternator.

Edited by ttoks

Location price and pics?. Is it r32 or r33 rb26?

engines from a 94 R32 GTR, still in car ATM (in the process of parting it out but need to buy a hoist to remove engine a box) after 9.5k complete or 7.5k as long motor, well under build cost of the engine, located in traralgon, vic 3844, about 2 hours east of melb.

if i can't get the receipts restored your welcome to remove the head and sump to verify it has the part's i've said it has.

engine.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...