Jump to content
SAU Community

Recommended Posts

This tells you what BUT I dont know how to fix

1 Right front wheel speed sensor or circuit

2 Left front wheel speed sensor or circuit

3 Right rear wheel speed sensor or circuit

4 Left rear wheel speed sensor or circuit

5 ABS right front wheel actuator solenoid or circuit

6 ABS front front wheel actuator solenoid or circuit

7 ABS rear wheel actuator solenoid or circuit

8 ABS actuator motor, motor relay or circuit

9 ABS actuator relay or circuit

10 ETS control unit power supply or circuit

11 Fore-and-aft G sensor 1 or circuit

12 Fore-and-aft G sensor 2 or circuit

13 Fore-and-aft G sensor 1, fore-and-aft G sensor 2

14 G sensor power supply 1 or circuit

15 G sensor power supply 2 or circuit

16 Lateral G sensor or circuit

17 Air bleed connector or circuit

18 ETS pressure switch or circuit

19 ETS motor, motor relay or circuit

20 ETS solenoid or circuit

21 Throttle sensor or circuit

22 ETS oil level switch or circuit

The capacitors inside the G-sensor leak and cause the sensor to stuff up. This could save you some money

http://www.skylinesaustralia.com/forums/topic/356654-r32-gtr-g-sensor-fix/

Edited by central coast person
  • 1 year later...
  • 3 months later...

Eats solenoid is located on your attesa pump, which is a over your rear diff, if it's a r32 or next to the fuel tank if r33/34.

In the manual there is a trouble shooting guide that guides t you through fault finding the issue.

  • 1 month later...

Next time it comes on open the boot and count the number of flashes on the Attessa ECU. It will pause and then repeat the flashes.

Once you have the count look up the code earlier in this thread - that should identify the issue and the fix

Edited by Sinista32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To back this up, I'm always looking on the outside, seeing the level, and then opening it up anyway, as I'm worried the level I've looked at, is more so a scunge line. Then you end up dipping your damn finger in it too depending on the type of tank you're looking at just to make sure I'm not going insane.   PS, Mark, polish up the none moroso one a bit and then give it a clear coat. The Moroso one looks to be way shiner (not mirror polished, just shinier) and it'll still look weird with the two different alloys beside each other. Either that, or Id probably paint them a flat black...
    • Good old Orange Park hey... 😛   f**k I miss that race track
    • lo, it was a death trap. Good times. Got any Fatz Drift Day DVDs still available?
    • Yes, overthinking. Many PS reserviors are completely opaque. Our Skyline ones, for example. Have to remove lid, peak inside, swirl the dipstick, try to remember how to read it, etc etc. Normal. Radiator overflows are often sufficiently opaque and scunged up that you can't see the true level inside anyway, and have to open and have a peak. Besides which, I replaced the (massively expensive, even back then) plastic overflow in my Alfa GTV, back in the '90s with a stainless one that I had a good fabricator make up to be dimensionally same-same, that looks remarkably similar to the Bogan's Moroso one above, and I never suffered any particular paranoia that I didn't know how much coolant was in it.
    • Looks great, but I'm always concerned that it makes it difficult to see what level the fluids are at. Am I overthinking this?
×
×
  • Create New...