Jump to content
SAU Community

Recommended Posts

I have an auto 33 gts , but it says all 1995 33 auto gas's have an rb20? I have an rb25?and how do I tell if my hicas works?

http://en.wiktionary.org/wiki/myne

just for everyone who doesn't speak 'lazy-teen'

I have an auto 33 gts , but it says all 1995 33 auto gas's have an rb20? I have an rb25?and how do I tell if my hicas works?

On your cluster you should have the word HICAS that gets highlighted for a few seconds along with ABS, Airbag etc when you turn the ignition on, if the HICAS stays highlighted permanently then theres usually something wrong with it.

i dont see how "myne" is easier to write than "mine".

Upon further consultation of my keyboard, i is closer to both m and n therefore, it would take substantially less time and effort to just type mine instead of myne and making this generation look stewpid.

I didnt draw attention to any of the other peculiarities, but now i will..

I have an auto 33 gts , but it says all 1995 33 auto gas's have an rb20? I have an rb25?and how do I tell if my hicas works?

What is a "gas's", and how does it relate to your NA R33 Skyline?

ea it says rb25 , just couldn't find my model on the net? :/And the only NA skyline to have a LSD is the series s gts25 or something?

What is "ea"?

Also, this isn't a jab at the OP, but how could you buy and own ANY car, not just a skyline, and not have any idea what model it is?

I understand that i am a car enthusiast, but isn't it standard procedure to find out at least what model car you are purchasing before you hand over your hard earned?

Edited by adamskill

I didnt draw attention to any of the other peculiarities, but now i will..

What is a "gas's", and how does it relate to your NA R33 Skyline?

What is "ea"?

Also, this isn't a jab at the OP, but how could you buy and own ANY car, not just a skyline, and not have any idea what model it is?

I understand that i am a car enthusiast, but isn't it standard procedure to find out at least what model car you are purchasing before you hand over your hard earned?

5 bucks says he's on his p's and has no clue what car he drives other than skyline!

Make a few spelling mistakes cause I'm getting used to my iPad On my L plates , first car..Appreciate lots of different cars......Sorry for asking for some help and people just dribble on about spelling when it's fine to read? Sit down you clowns....if your Gona be funny go for it , if your not then dont waste your time , twats

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...