Jump to content
SAU Community

Recommended Posts

just went to use fc edit today and it wont log at all..

yesterday it worked fine.

it gets correct delta an1-an2 readings in the monitor screen from wideband (3v, approx 14 a/f)

( all "datalogit" boxes in monitor screen are ticked)

checked the lm programmer and fc edit auxiliary settings were at 0-5v 9-16 a/f

delta an5-an6 wont un tick for some reason

if i hold down F1 on the monitor screen i can get a constant reading of values but starting a log only takes the momentary value.

will not put any values in to map watch.

any1 have an idea on whats gone wrong?

Edited by flame_this
Link to comment
https://www.sau.com.au/forums/topic/393994-fc-edit-problem-wont-log/
Share on other sites

do you have the right input selected in the drop down box on the map watch screen? it changes depending on delta settings and which input you use. do any other inputs show up on map watch (like knock for example)?

On the right side of of the monitor page, at the bottom, there are some check boxes. One along the lines of basic something or rather. Tick it then log again.

Edit nvm just read the op again. sau on my mobile isn't good.

Edited by SargeRX8

Are u sure the f2 button isnt stuck on causing the logging to stop?

thats what i was thinking at 1st

but turned out it was a broken serial- usb cable i was using.

updated the fc edit software to latest version and recognised the problem as "interface not responding"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...