Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

I got Enzed to put a barbed fitting in the banjo that bolts to the turbo, they dont have the same banjo so take yours(ive got a spare if u need)

Aushose down the road had some insulation as Enzed were all out of stock

i put the rubber hose from there to the back of the head, so only the back of the head has the two hose clamps.

good to know its going to be solid, thanks guys.

Ill try and get some pics for you.

No, pipe tools from plumbing shop, some shops only sell german and swedish tools so they cost heaps, ring around try Motorspares they are a goldmine of odd tools and parts, southern plumbing have some cheaper tools too

USE A HOSE CLAMP!

Imagine that hose coming off while your driving, spraying coolant all over a hot turbo.pinch.gif

I got Enzed to put a barbed fitting in the banjo that bolts to the turbo, they dont have the same banjo so take yours(ive got a spare if u need)

So I didnt read this line properly and I just went to Enzed and was stuck there trying to work out what I needed.

So do I cut my part off and they screw one into its place?

They did it for me, cut pipe and brazed the fitting on.

Just say some long haired scruffian had one done last friday, do it the same as that.

pirate.gif

*Edit*

Managed to speak to the guy who did yours Milk

He is going to knock it together for me this afternoon for $20

Spoke to the guys who have the heat sleeve and they are going to do that for me as well for $20

Should be able to get it all sorted by this afternoon

Now just to find something to cut this pipe

All i can say is, I really hope I dont have this issue with my r34 hi flow...

Also, my dad was a plumber and I daresay we have a shit tonne of copper pipe cutters of various sizes in the back shed so if you get real stuck with that let me know.

All i can say is, I really hope I dont have this issue with my r34 hi flow...

Also, my dad was a plumber and I daresay we have a shit tonne of copper pipe cutters of various sizes in the back shed so if you get real stuck with that let me know.

Mitch after this I will have the confidence to build you a turbo haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...