Jump to content
SAU Community

Recommended Posts

I have a set of HKS foam filter's on my GTR.

Being used to dirt bikes, i always wash, clean and reoil my foam filters. But apparently these have a "dry" type filter element/foam.

How the hell can a "dry" piece of foam filter out all the dust? Doesn't it need oil?

Before i just go out and clean my hks foam filters and oil them.

Is there any particular reason why i should not?

Obviously don't over oil them... I just spray a light coating on a nice clean air filter and thats it (dirt bikes).

Just having a dry foam filter in my car makes me feel so uneasy.

Link to comment
https://www.sau.com.au/forums/topic/396725-dry-hks-foam-filter-questions/
Share on other sites

I have a set of HKS foam filter's on my GTR.

Being used to dirt bikes, i always wash, clean and reoil my foam filters. But apparently these have a "dry" type filter element/foam.

How the hell can a "dry" piece of foam filter out all the dust? Doesn't it need oil?

Before i just go out and clean my hks foam filters and oil them.

Is there any particular reason why i should not?

Obviously don't over oil them... I just spray a light coating on a nice clean air filter and thats it (dirt bikes).

Just having a dry foam filter in my car makes me feel so uneasy.

Do you have air flow meters with a heating element on said dirt bikes? The problem with wet-filters is the oil often gets onto your AFM's heating element which will cause you problems. Modern dry-filters are very very good, there is really no need to oil. For example, the AEM dryflow filter has proven 99.52% filtration efficiency. Most brands of filter (Apexi, K&N, HKS, Injen, etc) these days will be much the same, there's no gimmicks.

Do you have air flow meters with a heating element on said dirt bikes? The problem with wet-filters is the oil often gets onto your AFM's heating element which will cause you problems. Modern dry-filters are very very good, there is really no need to oil. For example, the AEM dryflow filter has proven 99.52% filtration efficiency. Most brands of filter (Apexi, K&N, HKS, Injen, etc) these days will be much the same, there's no gimmicks.

true.

I have a map ecu and therefore no afm i run a very very large unifilter cylinder pod filter thing and I oil it, sucks a little bit in but nothing to worry about unless you have afm's.

I do have AFM's, the GTR is pretty much stock other then a hiflow cat/quiet exhaust and the hks pods.

I cleaned my AFM's on Sunday, who would have thought they are ment to be red and not black? haha.

I understand oil can get through the foam, but wouldn't that be if you over oil it?

I am only thinking about oiling them because of the bad rep the HKS filter's have...hence the third post on this thread >_<

Edited by Booki

I do have AFM's, the GTR is pretty much stock other then a hiflow cat/quiet exhaust and the hks pods.

I cleaned my AFM's on Sunday, who would have thought they are ment to be red and not black? haha.

I understand oil can get through the foam, but wouldn't that be if you over oil it?

I am only thinking about oiling them because of the bad rep the HKS filter's have...hence the third post on this thread >_<

I would just get new air filters.

I dont totally squeeze mine out, more so like i'd do on my bike, but if you squeeze it out real well it'll be fine id say clean your afm's as a part of your service sched..

Yeah definitely. Cleaning the AFM's will now be part of my sched. Seeing as i have only had the car for about 20 days, i figured it would be a good idea to start checking things out and seeing what needs to be done. Looked like the prev owner had never cleaned them.

I have nice spread sheets for all my maintenance records for all the bikes/cars i own :)

I know alot of people over oil there filters, hence them throwing off afm sensor's.

I think i might give them a very thin oil coat and a wash and just keep my eyes on it to see if it lets any oil through.

I have over oiled my air filters on dirt bikes before when i was new to them. But you get a good idea on how much is too much and how much is enough after you have done them enough times.

Hks filters are crap. Might as well not run one

I am actually interested to know why you think that.

I have read it alot, but havn't really seen any hard evidence on why they are bad.

Only reason i can think of is because they are "dry" ;)

On a completely unrelated note to this thread.

I checked my power steering fluid (least i think it is, the container near one of the AFM plugs), is a bit low.

Should this be changed out or just topped up? if so does the GTR take a particular type of fluid? Or can i just grab the generic stuff from super cheap.

If it needs to be changed, is it hard to do?

I am actually interested to know why you think that.

I have read it alot, but havn't really seen any hard evidence on why they are bad.

Only reason i can think of is because they are "dry" ;)

The HKS Mushroom filters don't get called "Poisonous Mushrooms" without due cause...

They tend to break up and send shit through the intake if you don't inspect them at each service to ensure they aren't stuffed. I've seen the inside of one, wasn't cool.

Take this chance to either

1. Get a stock airox which will be better

2. Replace them with Apexi or similar, and build a proper CAI box.

Both will offer far better reliability, and increased performance over rubbish exposed pods. Win-win really.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
    • Continental have consistently beaten the absolute shit out of every other performance tyre in Wet/Damp/Cold conditions and give up a little bit of time (half a second at most) in the dry. Almost like it's engineered for German conditions or something. I'd def give those a try.
×
×
  • Create New...