Jump to content
SAU Community

Recommended Posts

Wanna go back to the drags but only got chinese tyres which also are old n hard.

But need some new tyres, better quality an newer, was considering some KU36's.

first time i went to willowbank ran some falken 452's an managed a best of 1.59 60ft. would ku36's give better traction? Problem i can see is i dont know how to warm the tyres, so would cold ku36's be any grippier then falken 452's?

as i noticed last time as it got latter in the nite n cooler my 60ft times were slowly getting worse, tho mph was goin up so the times stayed the same (11.7)

also is there an easy way to warm ur tyres in an 33gtr?

any experience or advice/tips would be greatly appreaciated =)

Link to comment
https://www.sau.com.au/forums/topic/397038-tyres-for-dragstreet/
Share on other sites

If it's a relatively stock GTR - 1.60 for street tyres is pretty reasonable. You'd struggle to get much better on street tyres, maybe 1.5. Tyres aren't 'as important' as you don't really have the power to turn them (if its stock-ish).

No easy way on a R33 GTR to warm tyres, just drop the pressures down to around 20-22psi, avoid the wet ground for burnout start and away you go.

Has 420hp atw (think thats bit over 300kwatw) about 40hp more then when i was there the first time, seen a couple gtr's one with bout 320hpatw an one with 460hp that couldnt get traction first i think had pretty cheap rubber but the 460hp one had fairly mid range 265 rubber (cant remember brand) an couldnt get traction till 2nd gear an started to brake traction again an only managed a 12.4 maybe 12.3

just know every 1/10of a second off the 60ft is worth a fair bit more at the end... tho my original goal was to crack 200km/h at the end of the strip, 60ft might not count much towards that (top speed so far was 189km/h @ 380hp atw)

tho a quick 1/4 mile slip quietens the supercharged commordore boys kw bragging! :rofl:

yer i always went around the water, but there was a definate change in 60ft times as the air got cooler, an the tryes cooled down, first runs tyres were still a lil warm from driving there, latter runs the car had been sitting still for a fair while.

so do u think ku36's or a simalar tyre would get beta grip when cold then a normal street tyre?, plz recommend a different tyre if u think they're beta, but the tyres need to be drivin on the street, on a daily basis so dont want "drag" only tyres. i guess i could put it into limp mode.. but would be a lil annoying tho would be worth a go...

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...