Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Have ya tried a stock cas to fix the misfire?

Haven't tried anything Pete. I just haven't driven it. That's an easy test to do though. I believe it's a hot join in the coil pack loom as I have deleted the standard igniter and running an aftermarket one. Now with the moving around of that loom It might have buggered one connection. That will now be redone with a plug. On the dyno it's at exactly the same point, on the road it changes with load, gear and ambient temp. Fkn shit thing.

Love the build mate!!

Regarding the misfire, have you checked the coilpacks are getting a strong constant power? I had a shitty misfire once which was the constant power in the loom dropping due to a dirty/coroded loom plug.

Love the build mate!!

Regarding the misfire, have you checked the coilpacks are getting a strong constant power? I had a shitty misfire once which was the constant power in the loom dropping due to a dirty/coroded loom plug.

Thanks mate. I haven't, no. The loom itself is no more than 5000 Kms old. It was all fine the night I popped the engine, now this BS.. Yavuz will sort it. :)

  • 2 weeks later...

I have a great suggestion on custom plates for ur car...GR8WHT (as in great white shark)

That costs money. Haha.

Bit of a delay getting out there. Looks like Friday or Saturday at this stage.

Finally made it to UE yesterday. Woohoo!

A few little things going on like staging the fuel pumps under "X" RPM or Boost. (No needs to have two feed 044's buzzing away on the freeway heating fuel and pissing me off). Obviously the stupid missfire will be looked at and a tune with some decent boost and RPM. ATM its sitting at 380 rwkw at 19 psi with 7000 RPM being used. A bit of cam timing to be played with (not for outright power but the broadest area under the curve I can achieve). Might chuck a 30 PSI run in there to see how much these little snails can make.

A picture I took of the sperm whale a few weeks ago after I gave it a wash. Currently it has Nismo LM GT 4's in bronze borrowed from Joey's car.

20130203_174448_zpsa295d818.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...