Jump to content
SAU Community

Complete R33 Gtr Series 3 Rb26Dett Engine

Blitz
 Share

Recommended Posts

Blitz Grand Master

Blitz

Posted
Posted

Hi all,

I have for sale my RB26DETT engine setup out of my late model Series 3 R33 GTR.

This engine is in excellent condition and in stock standard trim, right down to stock turbo's, dump pipes and injectors.

To give you some background, I purchased my GTR as a Grade 4.5 with 84,000 Km's from Japan in late 2009 after an extensive search for the right car, and with the exception of a cat back exhaust and Power FC, the the engine was and remains standard. Once the car arrived it was given a full 100k service including new Timing Belt, Water Pump. full fluid flush, plugs, then

a compression test which revealed perfect results across all 6 cylinders, and finally a dyno tune for safety which was performed at one of Sydney's premier GTR building workshops.

The car has been used only very sparingly since coming into the country as plans for a build were put in place almost immediately, and has now covered only 87,000's

The engine has been religiously serviced, or rather pedantically over-serviced at my request by Just Jap Racing in Sydney using only the best Motul lubricants and fluids.

The reason for sale is I have been slowly building up a complete brand new engine from scratch which is now ready to drop in, and as such the current engine setup needs a new home.

As I mentioned, I am selling the engine in assembled long form including the following:

- Complete Long Engine (Head covers to sump)

- Intake & Exhaust side (Stock Plenum, Injectors, Fuel Rail, Turbos & Dumps)

- Stock Radiator (If Required)

The engine is currently still in my car, and is due to come out by the end of this month.

Interested buyers can see, hear and experience the engine running before it is removed.

I am located in Sydney, and the engine will be avaialble for pickup, or alternatively, I can arrange to have it freighted anywhere in Australia at the buyers expense.

Asking $3800.00 Firm

No stupid offers thanks.

Cheers.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...