Jump to content
SAU Community

Recommended Posts

Genuine WALBRO 400LPH Fuel Pump


- Most popular in-tank performance fuel pump on the market today

- 400LPH supporting 750+HP applications

- Genuine WALBRO – manufactured in USA by TI Automotive (box may be generic TI)
- Comes with 2x free strainers and kit

- Most popular upgrade across the Nissan range; RB's, SR's, CA's ect.

$190 $180 incl. Delivery >> SAU Special


E85 compatible version now in stock - 460LPH - $220 incl. Delivery

BUY_BUTTON.gif

* This is an Australian delivered product with a national warranty.



FP400_350.jpg


EFP-324_Dimension.jpg

whats the eta to sydney brookvale 2100 and will this be a direct fit into a 1999 nissan stagea 260rs?

Hi,

I can have one at your doorstep by Monday.

In terms of installation it is a relatively easy install across the Nissan range - very popular choice of in-tank pump!

One thing to note is you will need to wire a separate power supply and relay because Nissan's don't run a constant 12V at idle which the pump may not like.

I have double checked this with a full-time tuner in Melbourne that installed plenty of these.

- Brendan

Hi,

I can have one at your doorstep by Monday.

In terms of installation it is a relatively easy install across the Nissan range - very popular choice of in-tank pump!

One thing to note is you will need to wire a separate power supply and relay because Nissan's don't run a constant 12V at idle which the pump may not like.

I have double checked this with a full-time tuner in Melbourne that installed plenty of these.

- Brendan

thanks

  • 4 months later...

Are these the e85 compatible pumps?

Guys use them on e85 however we will be getting delivery of the e85 specific ones from Walbro within the next 2-3 weeks!

- Brendan

  • 3 weeks later...

Are these the e85 compatible pumps?

Those Walbro E85 pumps are in! 460LPH comes with strainer and terminal - $260 incl. delivery

Hurry as stock is super limited - 2 left



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...