Jump to content
SAU Community

Finally Ordered What Im Getting!

51NNA

By 51NNA,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

zebra Grand Master

zebra

Posted
Posted

hey guys i made a video, can i start a new thread...

Only if you post links to everything involved with your car right back to when it left the factory

Including the type and brand of pen used to write in the log book

ARTZ Grand Master

ARTZ

Posted
Posted

Only if you post links to everything involved with your car right back to when it left the factory

Including the type and brand of pen used to write in the log book

nah...too hard ill just whore up the kando thread some more...

Bsa Mentor

Bsa

Posted
Posted

Nice shopping list it's a shame tho why make a pointless thread asking to be ass fisted? Also 300kw why didn't you t67 or td06h 800 delivered? Also didnt it say those injectors are low impedance? Rb25 is high impedance. Man no offense but putting shit up like this is making you look bad and eventually no one will help you out because your acting like a c**t

51NNA Community Regular

51NNA

Posted
  • Author
Posted (edited)

LOL. you musnt have anything better too do then troll? lol. small minds ha.

What boost controller will u be using?

Its got a HKS Electronic boost controller in it now but its old and shit, i was just going to buy the Haltech controller, so the ecu will control everything.

Edited by 51NNA
Bsa Mentor

Bsa

Posted
Posted

Dude iv played with cars you could dream about I'm not a moron. It sure does but your building a drift car not a time attack car you don't need half the shit your buying chances are the things you replace will cause more to break. If I was building a drift car I would. Kando turbo, nismo injectors, PFC or nistune, decent cooler, e85 and a good cooling system then spend the rest of my 10 g on making it handle and safe then start saving for spares

51NNA Community Regular

51NNA

Posted
  • Author
Posted

I was thinking i might of been going overboard on the engine mods, ive worked out roughly ile be spending around 3-4k on the suspension setup, ile build the cage myself so that saves 3-4k on that alone lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...