Jump to content
SAU Community

Recommended Posts

Hey All,

My old for sale thread sorta just got added to and is old and messy now.

Thought I would start a new thread that actually had the items for sale listed.

All items are located in North Brissie. (unless stated)

Postage can be arranged, at buyers expense.

My best contact is either mobile 0428142684 or email [email protected]

rb26 coil packs - $200 ono.

These are standard coil packs, spares from one of the 4 engines I had at one point, but were in working condition when the engines were stripped.

sard 800cc injectors - $600

These have about 5000km of use on them. I wil be upgrading to higher flowing injectors. - does not include fuel rail.

AP racing 6 pot calipers, 354mm 2 pieces rotors and fitting hardware - $4300

These have about 5000km of use on them, mainly just daily street driving, have seen about 5 laps of QR and performed wonderfully.

Greddy plenum - $800

This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly.

Stock rb26 plenum - $150: LOCATED IN TOWNSVILLE

This is off one of the engines that I had that got stripped, only the plenum, no throttle body assembly.

post-39837-0-47555100-1334923847_thumb.jpg

post-39837-0-80276700-1334923858_thumb.jpg

post-39837-0-55250200-1334924037_thumb.jpg

post-39837-0-92392000-1334924144_thumb.jpg

injectors fully sold.

items still available:

rb26 coil packs - $150 ono.

These are standard coil packs, spares from one of the 4 engines I had at one point, but were in working condition when the engines were stripped.

AP racing 6 pot calipers, 354mm 2 pieces rotors and fitting hardware - $4300

These have about 5000km of use on them, mainly just daily street driving, have seen about 5 laps of QR and performed wonderfully.

Greddy plenum - $800

This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly.

Stock rb26 plenum - $150: LOCATED IN TOWNSVILLE

This is off one of the engines that I had that got stripped, only the plenum, no throttle body assembly.

Open to offers people, worst I can say is no thanks.

bump.

and back on the market, if anyone is interested...

short motor component of my engine. Done about 5000km as well.

N1 Block

Tomei 2.8L cooling channel type kit (pistons, rods, crank)

Tomei oil pump

ATI 1000hp type balancer with the pulley for the water pump.

Tomei sump baffle.

um... *shrug* 10k?

Tomei oil pump sold.

This is as far as I want to split it, as if i decide to keep the bottom end i it is getting dry sump.

rb26 coil packs - $150 ono.

These are standard coil packs, spares from one of the 4 engines I had at one point, but were in working condition when the engines were stripped.

AP racing 6 pot calipers, 354mm 2 pieces rotors and fitting hardware - $4300

These have about 5000km of use on them, mainly just daily street driving, have seen about 5 laps of QR and performed wonderfully.

Greddy plenum - $800

This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly.

Stock rb26 plenum - $150: LOCATED IN TOWNSVILLE

This is off one of the engines that I had that got stripped, only the plenum, no throttle body assembly.

  • 3 months later...

Greddy plenum - $800 $700

This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly.

NPC twin plate clutch - $1200

This was in my old r32 GTR. held approx 500hp with no drama's. Was told it should hold up to around 1000hp.

Solid centre, but still fine to drive on the street. I drove it a few times in brissie peak hour with no hassle.

If you want pics let me know and I can email them or text them.

Greddy plenum - $800 $700

This has about 5000km worth of use through it, runs the 6 throttle bodies still. - does not include throttle body assembly.

NPC twin plate clutch - $1200

This was in my old r32 GTR. held approx 500hp with no drama's. Was told it should hold up to around 1000hp.

Solid centre, but still fine to drive on the street. I drove it a few times in brissie peak hour with no hassle.

If you want pics let me know and I can email them or text them.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...